Arktic 233238 v.02 Manual Del Usuario página 9

or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle
greater than 5° and it is necessary to wait 2h before connect-
ing it to the power supply to switch it on. The same applies if
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
Intended use
• This appliance is intended to be used for commercial applica-
tions, for example in kitchens of restaurants, canteens, hos-
pital and in commercial enterprises such as bakeries, butch-
eries, etc., but not for continuous mass production of food.
• This appliance is designed only to keep food or beverages,
under cool state and to display them. Any other use may lead
to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Glass door
2. Air suction
• Never block the suction. Air is sucked in and cold air in
circulated inside the refrigerator.
3. Main ON/OFF switch
4. Rack
• The height of rack is adjustable for various goods. For ad-
justment :
1) Take out the rack
2) Move the rack support on suitable height.
3) Put the rack on the support.
5. Air outlet
• Never block the air outlet. Let inside circulating cold air
flow out.
6. Digital temperature controller
7. Air duct outside the glass to remove the condensation water
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig.2 on page 3)
8. Increase button
9. Light
10. Setting button
11. Decrease button
12. Refrigerant LED
13. Defrost LED
Circuit diagram
(Item 233238 v.02, 233269 v.02, 233610 v.02, 233627 v.02,
233634 v.02, 233641 v.02, 233658 v.02, 233665 v.02)
(Fig.3 on page 4)
A. Defrost probe
B. Thermostat probe
C. Digital Temperature Controller
D. Display panel
E. Power switch
F. Fan Motor
G. Over Load Protector
H. Compressor
I. Lamp
J. PTC
Circuit diagram
(Item 233290, 233696)
(Fig.4 on page 4)
K. Defrost probe
L. Thermostat probe
M. Digital Temperature Controller
N. Display panel
O. Fan Motor
P. Over Load Protector
Q. Compressor
R. Lamp
S. PTC
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Connect the power plug with a suitable electrical outlet.
Switch on the appliance (if it is included). Leaving the appli-
ance for running some hours to reach the cooling tempera-
ture before placing the beverage or food inside the appliance.
• Digital temperature controller operation
1). Setting the temperature
• Press (10) to enter into the setting mode. The set tem-
perature is displayed.
• Press (8) or (11) to increase or decrease the set tem-
perature.
• Press (10) again to confirm the setting and exit. Then,
inside cabinet temperature is displayed.
GB
9