Proper Use - Scheppach FS3600 Traducción Del Manual De Instrucciones Original

Prevent body contact with grounded surfaces such
as pipes and radiators. Please be watchful. Do not
work at the machine if you are tired.
Always wear:
• ANSI- approved dust masks.
• Safety glasses
• Hearing protection.
Do not stretch yourself over running machines.
ADDITIONAL INSTRUCTIONS
FOR LEAKAGE CURRENT CIRCUIT-BREAKER.
Please observe the following important instructions
on start-up and handling.
Pay attention to the instructions even if you hand
over the product to a third party. Preserve this oper-
ating Instructions manual for subsequent reference.
SAFETY INSTRUCTIONS!
• Arbitrary alteration and/or modification of the prod-
uct is not allowed for safety- and approval reasons
(CE). Never dismantle the product.
• The product is not suitable for handling by children.
Children cannot assess the risks involved in han-
dling electrical devices. Therefore, pay special at-
tention to the presence of children.
• The structure of the product corresponds to Pro-
tection Class 1. Only a proper mains socket with an
earth wire (230V~/50Hz) of the public power sup-
ply should be used.
• In industrial equipment, the Accident Prevention
Specifications of the Federation of Trade Associ-
ations for Electrical Systems and Resources must
be observed.
• In schools, training centres, hobby- and self-help
workshops, the operation of the product must be
monitored responsibly by trained staff.
• Handle the product carefully. Impacts, hits and
drops from even low heights can damage the ma-
chine.
• Never use the product if it is brought from a cold to
a hot room. Under certain circumstances, the re-
sulting condensed water can destroy the product.
• Let the product come to the room temperature, be-
fore connecting it to the mains power supply. Un-
der certain circumstances, this can take several
hours.
• Do not hold the product with moist or wet hands.
• Ensure that the Insulation of the entire product is
neither damaged nor destroyed.
• If the product is not operated over long periods,
disconnect it from the mains power supply, pull the
plug out of the socket.
• Avoid the following environmental conditions at the
installation site or during transport.
• Wetness or very high humidity. Extreme cold. Dust
or combustible gases, vapours or solvents. Strong
vibrations.
• Strong magnetic fields as in the vicinity of ma-
chines or loudspeakers.

9. Proper use

The machine corresponds to the valid EU Ma-
chine Directive
• Before starting work, all the protection- and safety
devices must be installed on the machine.
• The machine is designed for operation by one per-
son. The operator will be responsible for the pres-
ence of third persons in the work area.
• Observe all safety- and danger instructions on the
machine.
• Keep all safety and danger instructions near the
machine in complete and readable form.
• The machine is designed exclusively for cutting
small and medium-sized tiles (glazed, ceramic or
similar tiles) with the offered tool and accessories.
Cutting of metal and wood is not allowed.
• The dimensions of the workpieces to be machined
should not exceed or fall below the specified max-
imum and minimum dimensions.
• Please use the machine only if it is in a technically
fault-free condition. Use It properly, conscious of
the involved safety and risk factors and giving due
consideration to the operating instructions manual!
Faults, especially those that can affect safety must
be rectified immediately!
• The safety-, workplace- and maintenance spec-
ifications of the manufacturer as well as the di-
mensions specified in the technical data must be
observed.
• The applicable accident prevention measures and
the other generally recognized technical safety
rules must be observed.
• The machine must be used, serviced or repaired
only by persons who are familiar with it and who
have been briefed about its risks.
Arbitrary alterations to the machine will make the
liability of the manufacturer for damages resulting
there from null and void.
• The machine may be used only with original ac-
cessories and original tools of the manufacturer.
Residual risks
Despite proper use, certain residual risk factors
cannot be eliminated fully. The following things can
occur, depending on the design and structure of the
machine:
• Intervention in the running diamond cutting disc.
• Contact with the diamond cutting disc in exposed
area.
• Ejection of work pieces and work piece compo-
nents.
• Ejection of a faulty diamond attachment in the cut-
ting disc.
www.scheppach.com
GB | 23