DWT EX03-125 D Manual Original página 22

• Put the polishing accessory on the sanding plate 6�
Follow the rules below:
• the polishing layer should be on top (adhesive
surface of sanding plate 6 must be attached to the
adhesive surface of the polishing accessory);
• the brims of polishing accessory and sanding
plate 6 must match�
• Firmly press the polishing accessory against the
surface of sanding plate 6�
Attention: when pressing the sheet,
ensure that the polishing accessory
remains properly placed on sanding
plate 6.
Using the dust bag
During work, always use dust bag 8�
One should monitor dust level in dust bag 8 and empty
the bag at relevant time, taking the aforesaid precau-
tions�
Mounting / dismounting of the dust bag (see
fig. 5)
• To mount, insert the connecting pipe of dust bag 8
into the dust removal port 5 (see fig. 5).
• To dismount, pull out the connecting pipe of dust
bag 8 from dust removal port 5�
Emptying the dust bag (see fig. 6)
• Disconnect the power tool and remove dust bag 8 in
the manner described above�
• Remove textile bag 14 from the plastic body 13 (see
fig. 6).
• Taking the precautions described above, empty the
content of textile bag 14 by shaking, for better results,
turn the bag inside out and use a soft brush to clean it�
When washing textile dust bag 14, use it only after
the bag has dried completely.
• Put textile dust bag 14 on plastic body 13�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
tool on / off
[EX03-125 D, EX03-150 D]
Switching on:
Move forward on / off switch 4�
Switching off:
Move backward on / off switch 4�
[EX03-125 DV]
Short-term switching on / off
To switch on, press and hold on / off switch 4, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch 4 and lock it in the position with
lock-on button 10�
Switching off:
Push and release on / off switch 10�
Dust collection decreases dust concentra-
tion in the air and prevents build up of dust at
the work station�
Use of vacuum cleaner
During prolonged wood machining or when processing
materials that produce dusts hazardous to health, the
power tool should be connected to a proper vacuum
cleaner�
Given power tools may cooperate with the vacuum
cleaner only when used with a relevant connector�
One should monitor dust level in the bag and empty the
bag at relevant time, taking the aforesaid precautions�
Oscillation rate regulator
[EX03-125 DV]
The oscillation rate regulator 9 is purported to set the
desired oscillation rate of sanding plate 6�
• Push on / off switch 4 and lock it in the position with
lock-on button 10�
• Set the desired oscillation rate�
The required oscillation rate depends on the type of
processed material, work conditions and must be set
on the basis of practical trials for best results�
During prolonged work at low oscillation rate, one
should allow the power tool to cool down for 3 minutes�
For this purpose, set the maximum oscillation rate and
allow the power tool to work without load�
Sanding sheet selection
Prior to commencement of work, select the sanding
sheet 7 type that is most suitable for the processed
material or surface� The type of sanding sheet 7 is
specified on the package. One may also ask the ven-
dor for more information�
Various works require the use of sanding sheet 7 of
different coarseness, allowing a surface of required
smoothness to be obtained� The best method to select
sanding sheet, is to practically test for best results�
Sanding
Prior to commencement of work one
should perform test sanding on an un-
necessary element (made of the same
material or with the same coating as the
English
Автотовары «130»
21
Dust suction during
the power tool operation
Design features
of the power tool
Recommendations
on the power tool operation