EN
4. Sleep Mode - lf this setting is disabled,
this feature does not work. lf this set
ting is enabled, a message will appear
after the preferred time letting you
know that the device will enter sleep
mode. The auto power off function can
be set between 0-12 hours. The stand
ard setting is 3 hours. Press the STAND
BY button to exit Sleep/ Auto Off mode.
9.0ptions
To access the menu, press MENU and se
lect [Options]. The menu provides options
to adjust the OSD language, subtitle lan
guage and audio language. Select an op
tion and press RIGHT/LEFT to adjust the
setting. Press EXIT to exit the Menu.
1. OSD Language - Select the language of
the OSD.
2. Audio language - Select the preferred
audio language for watching TV chan
nels. lf the language is not available, the
default language of the program will be
used.
3. Subtitle Language - Select your pre
ferred subtitle language.
4. Digital Audio - Select the digital audio
output mode.
o.
1
System settings
To enter the Menu, press MENU and select
[System]. The menu provides options for
adjusting system settings. Press UP/DOWN
to select an option and press RIGHT/LEFT
to adjust the setting. Press EXIT to exit the
Menu.
1. Parental supervision - You can restrict
access to channels that are unsuitable
for children. To restrict/lock a channel,
you need to enter a password. The de
fault password is "000000''.
2. Set password - Set or change a pass
word for blocked programs. Enter
your old password or the default pass
word "000000''. After that, you will be
prompted to enter a new password. To
confirm, re-enter the new password.
After confirming, press EXIT to exit the
menu.
3. Restore factory default settings - Reset
the decoder to factory default settings.
In the main menu, select [Restore fac
tory settings] and press OK or RIGHT to
select. Enter your password or the de
fault password "000000" and press OK
to confirm. This option will delete all
preset channels and settings.
4. lnformation - View information about
the model, hardware and software.
11.USB
To access the Menu, press the MENU but
ton and select [USB]. The menu provides
options for playing music and photos. The
receiver supports MP3, WMA, JPG, BMP
files. The receiver only supports USB de
vices with the FAT and FAT32 file system. lt
does not support the NTFS file system.
1. Multimedia - lf no USB device is con
nected, a warning message"USB device
not found" will appear, otherwise you
can select music or photos and press
OK to go to the file browser and select
the file to play.
2. Configu re the display of photos
• Slide time: set the slideshow interval
to 1-8 seconds.
• Slide mode: Set the slide show effect.
• Aspect Ratio: Keep original picture
aspect. [Discard] displays the image
in full screen mode.
3. Configu re the display of movies
• Aspect Ratio:
[Keep]: Play back the movie in its
original aspect ratio.
[Discard]: Play the movie in full
screen mode.
• Subtitles:
[Small]: Display the subtitles in the
small mode.
[Normal]: Display subtitles in normal
mode.
[Large]: Displays the subtitles in large
mode.
• Subtitles background:
[White]: Display the subtitles with
a white background.
[Transparent]: Display the subtitles
with a transparent background.
[Gray]: Display the subtitles with
a gray background.
[Yellow-green]: Display subtitles in
yellow-green background.
• Subtitle font color:
[Red]: Displays the subtitles in red.
[Blue]: Displays subtitles in blue.
[Green]: Display subtitles in green.
Attention!
• We cannot guarantee the compati
bility (operation and/or power sup
ply) with all USB storage devices and
are not responsible for any data loss
that may occur when connected to
this device.
• The system may take a long time to
read the contents of the USB device
when the amount of data is large.
• Some USB devices may not be recog
nized properly.
• Even if they are in a supported for
mat, some files may not be played
back or displayed depending on the
content.
4. PVR configuration
[Recorder]: Select a disk for saving re
cordings.
[Format]: Format the selected disk.
EN