Functional Description - Dolmar SP-1815 Manual De Instrucciones

SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
(Fig. 1)
• Open Sprayer's battery pack cover.
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red part on
the upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not, it
may accidentally fall out of the tool, causing injury to
you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Spray pipe and nozzle assembly method
(Fig. 2)
• As shown in the diagram, assemble spray pipe and
then nozzle onto lever cock.
• Adjust direction of nozzle using nut on spray pipe.
• Firmly attach components to ensure there is no
leaking.
• Select nozzle according to type of spraying to be done.
NOTE:
• All connector units use packing. Before assembly,
always check to see that the units have packing.
• Check to make sure that the spray hose is not cracked,
worn and/or damaged.
• Firmly tighten on the spray pipe to prevent liquid leaks.
• If there is a leak from a connector unit, tighten further
using a hand tool (by approximately 45 degrees).
All manuals and user guides at all-guides.com
• Do not use a spray pipe that is longer than the standard
Back strap attaching method (Fig. 3)
Use the diagram pointers to attach the back strap at top
and bottom, making sure there are no twists in the strap.
NOTE:
• Check to make sure that back strap is securely
OPERATION
CAUTION:
• Before inserting the battery cartridge into the tool,
Spraying
CAUTION:
• To prevent sudden spraying, be sure to set the lever
• When spray work is interrupted, be sure to turn switch
Be sure to check the situation of surroundings before
turning sprayer switch ON.
Operate lever cock to spray.
Once spraying is complete, immediately set lever cock to
STOP, and then turn sprayer switch OFF.
How to use lever cock (Fig. 5)
1. Position "A" is the STOP position.
2. Position "B" is the spray position. Release the lever,
3. Position "C" is the continuous spray position.
NOTE:
• Check to make sure the tank is loaded with chemical or
• Running the sprayer for prolonged periods with the
• If spray splutters, or pumps suddenly screeches, the
• Do not spray with the battery cover open and/or with
• Do not forcibly handle the lever cock and/or the spray
Mixing chemical
CAUTION:
• Never use Kelthane water dispersible powder
one provided. Doing so may cause leaking from
connector units.
attached to chemical tank.
always check to see that the tool is switched off.
cock to STOP, before turning sprayer switch ON or
OFF.
OFF, to prevent inadvertent spraying. (Fig. 4)
and it will return to position "A" and spraying will stop.
(Intermittent spraying)
(Continuous spraying)
clean water when operating the sprayer, as continued
operation of the sprayer with an empty tank may burn
out the pump.
lever cock closed may have an adverse effect on the
pump as well as drain the battery. Be sure to turn
sprayer switch OFF whenever possible.
chemical tank is empty, so immediately turn sprayer
switch OFF.
the back-support cushioning removed, as there is a risk
of damage to electrical system. Moreover, do not point
the spray nozzle at the sprayer and spray.
pipe.
(acaricide) because it tends to harden due to heat
generated by pump during operation, which causes the
pump to stop. Use a Kelthane emulsion, Akar emulsion
or Osadan water dispersible powder as the acaricide.
7