Berner BACCS-2 BL 18V Manual Original página 36

between the time you release the trigger and when the
brake engages. Occasionally the brake may miss com-
pletely. If the brake misses frequently, the saw needs
servicing by an authorized Berner service facility.
You must always wait for the blade to stop completely
before removing the saw from the workpiece.
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended
exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be
kept clean.
For an optimum life-time, the battery packs have to be
fully charged, after use.Battery packs which have not
been used for some time should be recharged before
use.
To obtain the longest possible battery life remove the
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store
the battery pack where the temperature is below 27°C
and away from moisture Store the battery packs in a
30% - 50% charged condition ,Every six months of
storage, charge the pack as normal.
Do not dispose of used battery packs in the household
refuse or by burning them. Your power tool distribu-
tor will normally retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal
objects (short circuit risk).
Use only System Berner chargers for charging System
Berner battery packs. Do not use battery packs from
other systems.
Never break open battery packs and chargers and
store only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of con-
tact with battery acid wash it off immediately with soap
and water. In case of eye contact rinse thoroughly for
at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery
section of the charger (short circuit risk).
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short
circuit situations that cause high current draw, the tool
will stop for about 2 seconds and then the tool will
turn OFF. To reset, release the trigger. Under extreme
circumstances, the internal temperatur of the battery
could become to high. If this happens, the battery will
shut down. Place the battery on the charger to charge
and reset it.
ENGLISH
457 843 - Berner-BACCS-1 BL 18V.indd 36 457 843 - Berner-BACCS-1 BL 18V.indd 36
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous
Goods Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provi-
sions and regulations.
The user can transport the batteries by road without
further requirements.
Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to
be carried out by appropriately trained persons and
the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected
and insulated to prevent short circuit. Ensure that
battery pack is secured against movement within
packaging. Do not transport batteries that are cracked
or leak. Check with forwarding company for further
advice
MAINTENANCE
Be sure to disconnect the tool from the power supply
before attaching or removing the saw blade.
Clean tool and guarding system with dry cloth.
Certain cleaning agents and solvents are harmful to
plastics and other insulated parts.
Keep the apparatus handle clean, dry and free of spilt
oil or grease.
Check the function of guards.
Regular maintenance and cleaning provide for a long
service life and safe handling.
The ventilation slots of the machine must be kept clear
at all times.
Remove dust regularly. Remove the sawdust which
has accummulated inside the saw in order to avoid the
risk of fire.
Use only Berner accessories and Berner spare parts.
Should components need to be replaced which have
not been described, please contact one of our Berner
service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine
type printed on the label and order the drawing at
Berner.
36
02.08.2021 14:49:17 02.08.2021 14:49:17