GE Winterberry 5 Ft Instrucciones Para El Ensamblaje

5 Ft , 6.5 Ft & 7 Ft
Winterberry
ASSEMBLY INSTRUCTIONS
CAUTION: EXERCISE CARE WHEN UNPACKING AND ASSEMBLING
WARNING: Risk of fire and electric shock. Disconnect light set from power before starting.
1) Keep wires clear of being pinched or cut during assembly or installation.
2) Do not press or grasp bulbs during assembly or installation.
3) Before starting make sure stakes are clear of underground: sprinkler, telephone and
power lines.
4) Please read all instructions and warnings included with this product before using.
Approximate assembly time is 20 minutes
Hammer/Mallet may be required for stakes
NOTE: No tools required
Parts List:
(
1) Top section for all types
(1) Bottom section or Extender for all types
(1) Spare parts bag with metal stakes
Top section for all types
or
Bottom section
Extender for all types
Spare parts bag with metal stakes
1.Carefully unpack, removing any bubble pack and inspect the contents of your tree.
The spare parts bag is taped to end flap. Retain the shipping carton to repack your tree.
If applies, set aside any loose bulbs to reattach later.
NOTE:
2.Remove the tree stand from the storage bag and open. You may need to loosen the
thumbscrew to open base with legs.
your assembled tree may be heavy and difficult to move so place the stand in the
Hint:
desired location before assembling. Secure in place using the (4) metal stakes.
Stands with legs come with (1) thumbscrew either already threaded into the stand
NOTE:
or packaged separately in a bag. Make certain to locate the thumbscrew before discarding
the bag. If your stand comes with a thumbscrew, it is to be threaded into the stand. Insert
or back-out accordingly.
3.Look for the bottom section or the extender, identified by a red-colored plastic protective
cap at the bottom of the pole. Remove the cap and place into the tree stand. If your stand
has a thumbscrew, fully tighten the thumbscrew.
4.Locate and untwist the red metal tie wrap holding the branches in place. Save this tie
wrap to use when storing your tree.
If your branches do not fall into place, DO NOT force down. Starting at the bottom
Hint:
gently lift up on the branches to release them from their locked position. During shipping,
branch tips may become intertwined or entangled. Carefully undo. Now, all rows of
branches should be in the open position. Locate the long lead wire and place it to the side
for later use.
10"X10"
Branch Tree
®
(1) Middle section for most
(1) Metal stand with legs or flat base
Middle section for most
or
Metal stand with legs flat base
: If the top and bottom poles are electrically connected or if
NOTE
your tree has only two sections, skip to step 7.
5.Remove the green protective cap from the middle section.
Find the locating key inside opening. Find groove at top of
the bottom section. Insert the middle section over opening in
bottom section. Rotate slightly until it slides down and is
fully seated. Keep all wires from entering the opening and
damaging the wires.
This stabilizes your tree keeping both sections from
NOTE:
turning and properly aligning the branch panels.
6.Untwist the red metal tie wrap holding the branches in place. Refer to Hint in 4. Save for
storing the tree.
7.Insert the treetop into the opening of the lower section and shape, being careful to keep
the cord from entering the opening and damaging the wires. Straighten out the top tips if
necessary.
8.Depending on the Model of your tree electrically connect the lighted sections following
either a) or b) below:
a) End Plugs - Fully insert the plug from the top pole into the end connector near the top of
the lower pole. Continue down to connect the bottom if your tree has (3) lighted section.
b) Connectors – First find the 2 yellow CONNECTOR cord tags located between each section.
First align the 2 pins and flat on the connector and then fully inserting into the other connector.
Fully screw on the cap to secure together. Repeat if your tree has (3) lighted sections.
Reattach any loose bulb by fully inserting into an open lamp socket.
NOTE:
Your winter Christmas tree is now assembled!
9.To illuminate find and unhank the long lead wire from the bottom lighted section.
Fully insert the plug directly into a working GFCI outlet or an outdoor rated extension cord.
10.Some Models have a dual color, 4-function control box. The functions are: Steady White,
Steady Multi, White & Multi Color Change and Off.
11.Please check your tree for any loose, unlit or damaged bulbs. They must be replaced
promptly in order to maintain the performance and life expectancy of your pre-lit tree.
Your winter Christmas tree
is now complete!
Note:
Always unplug this product
before installing. Do not plug in, until
entire tree assembled.
Troubleshooting Tips
If one section of your tree does not illuminate,
check that section for loose or missing bulbs or
that all electrical connections on tree are made.
Also, check the fused plug for a missing or
burned out fuse and make certain the wall
switch is turned on.
Tree Storage
When your tree is not in use, be sure to store it
neatly in a cool, dry location protected from
sunlight.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Inc.
Distributed by Nicolas Holiday Inc.,
Indoor/Outdoor
©
2016 Nicolas Holiday Inc.,
9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560
All rights reserved.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
5BWB16
Printed in China