Product Operation; Parts And Maintenance - Ingersol Rand IQV12 R1120 Manual Del Usuario

Product Information: Cordless Ratchet Wrench
Product Safety Information
Intended Use:
These Cordless Ratchet Wrenches are designed to remove and install threaded fasteners.
• Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury. Save all warnings and instructions for future reference.
• Responsibly recycle or dispose of Batteries. Do not puncture or burn Batteries. Improper disposal may endanger the environment or cause
personal injury.
• Only use Tools with appropriate voltage Ingersoll Rand Batteries and Charger. Use of any other batteries may create a risk of fire, personal
injury or property damage.
For additional information, refer to Cordless Ratchet Wrench Safety Information Manual Form 80232929, Battery Charger Safety
Information Manual Form 10567832 and Battery Safety Information Manual Form 10567840.
Manuals can be downloaded from ingersollrandproducts.com.
Product Specifications
Voltage Drive
Tool Battery
Model Model
V, DC
R1120 BL1203 12
R1130 BL1203 12
† K = 3dB measurement uncertainty
pA
‡ K = 3dB measurement uncertainty
wA
*K = Vibration measurement uncertainty
Conforms to UL STD. 60745-1 & 60745-2-2.
Certified to CSA STD. C22.2 No. 60745-1 & 60745-2-2.
When using this product as a manually-operated ratchet wrench, do not exceed the maximum torque listed in the table. Exceeding this
torque may cause damage to the product and will void the warranty.

Product Operation

These models feature a variable trigger and an automatic shut-off.
The variable trigger feature allows an operator to regulate the power output of the tool through manipulation of the trigger lever. Power output
will increase as the trigger lever is pressed in, with maximum power output occurring when the trigger lever is fully depressed. Power output will
decrease as the trigger lever is released.
The automatic shut-off feature shuts off power to the motor when the motor is stalled. When tightening a fastener, the motor will stall when the
tool is unable to tighten the fastener any further, so automatic shut-off will occur at this condition. When attempting to loosen a fastener, the
motor will stall if the tool is unable to move the fastener, so automatic shut-off will occur at this condition also. When automatic shut-off occurs, the
trigger lever must be fully released and then pressed again to restart the tool. After automatic shut-off occurs, the tool can continue to be used as a
manually-operated ratchet, provided that the maximum torque limit specified for that particular model is not exceeded.
Lubrication
Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days and m=months of actual use.
30d
1
2
3m

Parts and Maintenance

All other maintenance and tool repair should only be carried out by an authorized Service Center. For the nearest location, visit
ingersollrandproducts.com
Refer all communications to the nearest Ingersoll Rand Office or Distributor.
47503004001_ed2
No Load Recommended
Speed Torque Range
inch rpm ft-lbs (N-m)
1/4 0-260 5-25 (7-34)
3/8 0-260 5-25 (7-34)
3
6m
IR #
70
Inject between ratchet
housing and yoke to
lubricate drive bushing.
WARNING
Sound Level dB(A)
Max. Torque
† Pressure (L
ft-lbs (N-m)
30 (40) 76
30 (40) 76
NOTICE
1 2
cm IR #
3
1 70
Disassemble ratchet head
and lubricate components.
Vibration (m/s
(EN60745) (EN60745)
) ‡ Power (L )
Level
p w
87 1.3
87 1.3
3
cm IR #
3
2 67
Disassemble gearing and
lubricate components.
EN
)
2
*K
0.6
0.6
cm
3
1
EN-1