Symbols; Operating Instruction; Cleaning And Maintenance - MaxPro PROFESSIONAL MPSG550/800V Manual De Instrucciones

• High pressure at the nozzle.
Recommenda Wear a breathing mask and safety glasses when spraying.
CAUTION - DANGER OF INJURY!
Never point the spray gun at yourself, at other people or at animals.
• When working with the tool indoors as well as outdoors ensure that no solvent vapors are sucked in by
the spray gun.
• When working outdoors, be aware of the wind direc
greater distances - thus causing damage. When working indoors, provide for adequate ven a
• Do not let children handle(4) the device.
• Never open the device yourself in order to carry out repairs in the electrical system!
• Do not lay the spray gun.
Residual risks
Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The
following hazards may arise in c
1. Damage to lungs if an eff ve dust mask is not worn.
2. Damage to hearing if eff ve hearing prot
3. Damages to health r from vibra
ately managed and properly maintained.
WARNING! This power tool produces an electromagne c field during opera
some circumstances interfere with ve or passive medical implants. To reduce the risk of serious or fatal
injury, we recommend persons with medical implants to consult their physician and the medical implant
manufacturer before opera

SYMBOLS

Read the manual
Warning

OPERATING INSTRUCTION

1.Connect gun body with motor(Fig.1)
(1).Hold the gun with your hand to align the slot on the gun with the slot on the motor and insert it (as shown
in the figure).
(2). Hold the motor handle with your hand, rotate the right hand clockwise 90°.
(3).When the gun and host are parallel, it is locked.
2.Unscrew the paint container from the spray gun.(Fig.2)
3.Adjust the suction tube.(Fig.3)
(1).If spray in an upward direction，the angled end of the suction tube should be pointing toward the rear of
the gun.
(2).If spray in a downward direction, the angled end of the suction tube should be pointing towards the front
of the gun.
4
Wind can carry the coa g substance across
ower tool's cons
worn.
emission if the power tool is being used over longer period of
This field may under
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
GB
4.Pour material into container, make sure not to exceed 800ml(Fig.4)
5.Adjust the needle adjusting screw to meet your requirement.(Fig.5)
(1).Adjust the screw to left to decrease paint volume, lower paint thickness.
(2).Adjust the screw to right to increase paint volume, increase paint thickness.
6.Spray length adjustment: Turn this knob to adjust the round shape from vertical to horizontal.
Adjust the required length according to the spraying environment, reduce waste and save material.(Fig.6)
(1).The counterclockwise rotation shortens the length, and when it rotates to the stop position, it is sprayed
with the largest circle.
(2).Adjust the screw to right to increase paint volume, increase paint thickness.
7.Adjusting spray patterns.(Fig.7)
(1).The gun spray patterns can be changed from a horizontal oval fan pattern to a round.
(2).detailed pattern to a vertical fan pattern by adjusting the nozzle.
8.Open the power switch, pull trigger, the paint will spray from the nozzle.(Fig.8)
(1).EVEN COAT THROUGHOUT.
Correct:Keep stroke smooth and at even spee.
Incorrect:Do not flex wrist while spraying.
9.VI Replace nozzle and Needle:(Fig.9)
(1).When disassembling the nozzle, please pull the trigger first, then press and remove the nozzle.
(2).As shown in the figure, rotate to remove the needle
(3).As shown in the figure, rotate to set up the needle.
10..Remove the motor(Fig.10)
(1).Hold the gun with your hand and press the latch in the direction of the arrow.
(2).At the same time hold the motor handle with your hand and rotate it counterclockwise 90°.
(3).Pull out to remove the motor from the gun.

CLEANING AND MAINTENANCE

Always remember to disconnect from the mains supply before cleaning the spray gun or paint container. (5)
It is essen at the spray gun is cleaned and oiled thoroughly a er every use. Failure to clean and
oil it will almost certainly result in blockages and it may not operate when you next come to use it! The
guarantee does not cover cleaning a sprayer that has not been properly cleaned by the user.
The follo st be taken a er every use:
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner that was used.
3. Pour some thinner into the container and spray through the spray gun un
out of the nozzle.
4. Thoroughly clean the paint pick up pipe and filter with thinner.
5. Clean the basket and nozzle and remove any other debris or paint that remains.
6. Turn the spray gun upside down and apply a few drops of light oil to the two apertures
7. switch on the unit for a while, this will lubricate the piston and cylinder.
If your spray gun should require extra internal cleaning, it may be necessary to disassemble it.
If so the follo taken:
3. Remove the plug from the mains socket.
4. Remove paint container (5), pick up pipe and filter.
5. Take off the pump assembly.
6. Release the nozzle (H), valve (I), piston (M) and spring (L).
7. Clean the cylinder (K) and all parts thoroughly with solvent.
8. Apply a few drops of light lubrica to the piston, spring and cylinder.
9. Reassemble the spray gun.
GB
coming
5