WMF Kult X Doppel Induktionskochfeld Instrucciones De Uso página 11

Using direct select programmes (8)
Action
Plug the appliance in. Appliance is in standby mode.
Tap the On/Off button; appliance is in operational readiness
mode
Position the pan on the hotplate.
Select programme. For example "Cooking/Steaming".
Adjust the power level if required.
Adjust the timer with + / - if required.
Tap the Start/Pause button. Cooking process and Timer
starts. The "Appliance in use" symbol is shown in the display
If necessary, tap the Start/Pause button again:
- Cooking process and Timer is paused
- The "Appliance in use" symbol disappears
- Start/Pause LED fl ashes
- Tap on the Start/Pause button to resume the Cooking
process and Timer
Once the defi ned timer time has elapsed, the appliance
switches automatically to operational readiness mode.
After one minute, the appliance switches automatically to
standby mode.
Alternatively, press the On/Off button.
Note: The fan runs on for a few seconds.
Pull out plug.
Note: If the induction hob is in pause mode it switches itself to standby automatically after 10
minutes if the control panel is not operated.
Additional instructions for use
You can change the cooking parameters at any time while cooking:
▪ Change the power level using the power level controller (within the range of the predefi ned
programme (8). See Programme table).
▪ Adjust the timer with the + and - (10) buttons.
▪ Change the programme by selecting another programme. In this case, the corresponding symbol
button must be tapped and held for 1 second. This prevents an accidental change of programme
from occurring.
Cleaning and care
▪ Pull out the mains plug before cleaning the appliance.
▪ Ensure that no water gets into the appliance.
▪ Never submerge the appliance, cable or plug in water or any other liquids.
▪ Do not use any cleaning agents that are abrasive or that contain benzine.
▪ Do not bring any fl ammable (infl ammable), acidic or alkaline material or substances close to the
appliance as this could shorten the appliance's working life and a burst of fl ame can occur when
switching the appliance on.
▪ Wipe down the ceramic area with a damp cloth or you can use a mild, non-abrasive soap solution.
▪ Wipe down the casing and control panel with a damp cloth or you can use a mild cleaning agent.
▪ Dry the whole appliance completely before next use.
20
Touch button Display
Errors
Problem: Cause:
The appliance is not working. The mains plug is not connected
to a socket.
The appliance cannot be started, There is no or unsuitable cook-
is beeping and the display is ware on the hob.
showing error message "E0".
The appliance switched itself off The appliance gets too hot.
during operation.
The set time has elapsed and the
appliance has ended the heating
process.
Display shows error message The over-/undervoltage protec-
"E01/E02". tion feature was triggered.
Display shows error message The overheating protection
"E03/E04/E05". mechanism has been triggered.
The indicator light of The appliance is on standby, the
the on/off button is on, but the heating function is not activated.
appliance isn't heating up.
The appliance was on standby The automatic shut-off feature
and switched itself off. was triggered as the appliance
was not in use.
Solution:
Plug the mains plug into a
socket.
Never use the appliance without
cookware. Only use cookware
that is suitable for use with
inductions hobs. Follow the
safety instructions for your
cookware.
Unplug the mains plug and clean
the ventilation slots if neces-
sary. Allow the appliance to cool
down.
If the food you are cooking is
not hot enough, extend the
cooking time.
Ensure appropriate power supply
to the appliance.
Switch off the appliance and
cool it down, unplug it from the
mains and switch it back on.
Select the type of operation, e.g.
operation by power level or by
direct select programmes.
Switch the appliance back on
when you want to use it.
21