ENFORCER SM-4601-LQ Manual

Industrial Wide-Gap
Magnetic Contacts
SM-4601-LQ / SM-4601-L3Q
Manual
SM-4601-LQ only
Specifications
Model
Loop type
Electrical configuration
Operation gap
Connectors
Case
Material
Contacts
Contact rating
Switch cycles
IP Rating
Operating temperature
Switch
Dimensions
Magnet
Magnet type
Installation
Please read the manual carefully before you begin the installation.
1. Mount the contact on the track in a safe location away from equipment interference and near where the
magnet will be when the door is closed.
2. Run the armored cable out of the way. Run wires from the alarm control panel and connect to the
corresponding wires extending from the cable armor.
3. Mount the magnet on the roll up door so that it will trigger the contact when the door is closed. Be sure
that the gap between the contact and magnet does not exceed 3" (76mm).
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov.
LIMITED LIFETIME WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for the lifetime of the product. SECO-LARM's
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. Under no circumstances will SECO-LARM be responsible for any
costs or charges for removal, installation, or reinstallation. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects
in material and workmanship. The sole obligation of SECO-LARM, and the purchaser's exclusive remedy, shall be limited to repair or replacement only, at SECO-LARM's option. In no event shall
SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products
sold and installed in the United States and Canada. For all other countries the warranty is 1 (one) year.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also
not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022 SECO-LARM U.S.A., Inc. All rights reserved.
16842 Millikan Avenue, Irvine, CA 92606
Phone: (949) 261-2999 | (800) 662-0800
SM-4601-LQ shown
SM-4601-LQ
Closed loop Open/closed loop
N.O. (SPST)
(Form C
3" (76mm)
36" (91cm) Leads
Aluminum
Iridium plated
1.0A@10VDC (max.)
10W (max.)
50 Million (0.1mA@5VDC)
IP65 Weatherproof
-15°~160° F (-25°~70° C)
3"x1"x / " (76x25x13 mm)
1
2
3"x1"x / " (76x25x13 mm)
1
2
Rare-earth neodymium
U.S.A., Inc.
 Useful for industrial situations where a wide-gap,
surface mount contact is needed
 36" (91cm) Wire leads enclosed in armored cable
 Contact switch has iridium-plating for a high
melting point and Vickers hardness for higher
power handling and a longer expected life
 Weatherproof (IP65) and sealed for outdoor use
 Rugged aluminum housing
 3" (76mm) Gap
 Mounting bracket included
 Lifetime limited warranty
Parts List
1x Contact switches
2x Mounting screws
1x Mounting bracket
Overview
SM-4601-L3Q
 Contact and magnet must be installed on
NO/NC  Wiring shown is for the SM-4601-LQ.
SPDT)
–
Website: www.seco-larm.com
Email: sales@seco-larm.com
1x Magnets
1x Manual
the protected side of the door.
SM-4601-L3Q will be different.
Alarm Control
Panel
MI_SM-4601-LxQ_220415_ML.docx
GND
N.O.
®
PICNN1