Publicidad
Idiomas disponibles
Idiomas disponibles
GB
ASSEMBLY INSTRUCTIONS
The type LA shower trays are manufactured for building in the floor, or for bricklaying. Both variants must
be done by an expert - bricklayer. The shower tray can be used in a niche by itself, or with any compatible
shower enclosure manufactured by the RAVAK company. We recommend that you complete the trays by
a siphon RAVAK BASIC (PROFESSIONAL) 90.
1a.b.
Remove the top siphon cover using a flat, blunt object
and take out the sludge trap. Using the shoulders on the
inside diameter, unscrew the siphon. Use a wrench of diame-
ter 90 mm to assemble.
2a,b.
Place the tray provisionally in the required position and
mark the location of the siphon on the floor. Next, mark the
height of the upper edge of the tray on the wall.
2c.
The upper edges should be level. The difference in height
(see the picture 2c) between the seat and the edge of the tray
has to be about 185 - 190 mm.
3a,b.
Make the outlet piping (diameter 40 mm) and prepare
the connection to the siphon.
4a,b.
Place the shower tray in its final position again, fit the
siphon correctly and mark the position of the pipe joint. Finish
the connection of the outlet pipes and bottom part of the
siphon.
5a,bc.
The new trays are modified for hanging from the edge
to clips on the wall. It is necessary to mark the centre of the
clip in a distance 100 mm from the corners of the tray. Drill a
hole (diameter 8 mm) 40 mm from the upper edge, space and
fit the dowel.
6.
Space out the clips (pict. 6), using 2 pcs on the higher
corner of the tray (seat). On both sides place them in a distan-
ce 100 mm from the corner of the tray. Then mount the angu-
lar tray TAURUS in the niche.
7a,b.
Screw on the plastic clip (the shorter claw up - see the
picture), check the fixing of the tray.
MAINTENANCE
Clean the plastic parts with a cloth and mild detergent. Never use strong cleansing or scouring agents,
alcohols, thinners or acetone. The manufacturer accepts no liability for any type of use or care other than
those contained in these instructions. The manufacturer reserves the right to introduce technical changes
without notice. The guarantee is 12 months from the date of sale. For further information about assembly,
use, and care contact your local dealer.
The manufacturer recommends the
remove old and dried-on debris from glass surfaces, shower frames, enamel and acrylic bathtubs,
washbasins and water taps;
bcterial and anti-fungal effects.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR tel.: 318 427 111, 318 427 200
fax: 318 427 269, 318 427 278, e-mail: smith@ravak.cz www.ravak.com
RAVAK ANTICALC
RAVAK DISINFECTANT
- Shower Trays with Laminate
Reinforcement -
8a,b.
Prepare the brick bed for the tray to the desired height to
fit the entire surface of the tray bottom. Apply a mortar layer to
a thickness of 20 - 30 mm to the surface of the bed.
9a,b.
Place the shower tray in the correct position, screw the
siphon gently and press the tray into the mortar bed in the
correct position. Check and adjust the horizontal position and
the height from the floor. It is necessary to apply the silicone
to the claw of the clip before the final setting.
10a,b.
Finish the assembly of the siphon.
11a,b.
The final walling-in or tiling cannot be done before the
hardening of the bed.
12a,b.
The tiling can be a maximum of 5 mm over the outside
edge of the tray.
Notice:
We recommend using a silicone sealing compound to connect
the tray with finished tiling or other surfaces. A better seal for
large joints is achieved if mortar is used first, and then
a silicone sealing RAVAK PROFESSIONAL compound. If
using another cement, there is a risk the tray will not be water-
proof. It is suitable to use the "Installation set for KASKADA
shower trays"which is produced by the RAVAK company, to
achieve a professional sealing of trays.
line of products:
RAVAK CLEANER
- is a special preparation with considerable anti-
Type LA
- works to
Publicidad
