Tabla de contenido
Manuales relacionados para Westinghouse Harmony
Resumen de contenidos para Westinghouse Harmony
- Página 1 ETL-ES-Harmony-WH11 Owner's Manual Manual del usuariO Harmony Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: net weight: 15.4 lBs Peso neto: 7.0 KGs...
- Página 2 ETL-ES-Harmony-WH11...
-
Página 3: Safety Tips
ETL-ES-Harmony-WH11 safety tiPs OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT", AND USE THE OUTLET SCREWS PROVIDED WITH THE OUTLET BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. -
Página 4: Consejos De Seguridad
ETL-ES-Harmony-WH11 COnsejOs de seGuridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTE EL VENTILADOR EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES”, Y UTILICE LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR. LA MAYORÍA DE LAS CAJAS DE EMBUTIR UTILIZADAS NORMALMENTE PARA ARTEFACTOS DE ILUMINACIÓN NO SON ADECUADAS PARA VENTILADORES Y DEBERÍAN SER REEMPLAZADAS. -
Página 5: Features Características
ETL-ES-Harmony-WH11 features CaraCterístiCas DOWNROD VAULTED CEILING INSTALLATION INSTALLATION INSTALACIÓN CON INSTALACIÓN PARA CIELORRASOS ABOVEDADOS VARILLA VERTICAL May require a longer downrod For normal ceilings Para cielorrasos normales (sold separately) Podría requerir una varilla vertical más larga (se vende por separado) -
Página 6: Preparing For Installation Antes De La Instalación
ETL-ES-Harmony-WH11 PreParinG fOr installatiOn antes de la instalaCión Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble). - Página 7 ETL-ES-Harmony-WH11 PreParinG fOr installatiOn PreParinG fOr installatiOn antes de la instalaCión antes de la instalaCión Check the motor for plastic shipping stabilizer tabs and remove them if they are present. Remove the clamp pin (1) from the cross pin (3) from the coupling (2).
-
Página 8: Mounting Bracket Installation Instalación Con Soporte De Montaje
ETL-ES-Harmony-WH11 MOuntinG BraCKet installatiOn MOuntinG OPtiOns instalaCión COn sOPOrte OPCiOnes de MOntaje de MOntaje Choose a MOuntinG OPtiOn elija una OPCión de MOntaje nOrMal dOwnrOd OPtiOn If installing downrod supplied with fan, proceed to page 9, step 7. OPCión COn Varilla VertiCal Para CielOrrasO nOrMal Si instala la varilla vertical incluida con el ventilador, proceda a la página 9, paso 7. - Página 9 ETL-ES-Harmony-WH11 nOrMal dOwnrOd OPtiOn OPCión COn Varilla VertiCal Para CielOrrasO nOrMal Insert downrod (2) into downrod coupling (5). Make sure to align hole in downrod with the hole in downrod coupling. Install cross pin (1) through coupling and downrod. Insert Place downrod assembly (2) into canopy (1), canopy cover ring (3) and coupling clamp pin (3) into cross pin until it snaps into place.
- Página 10 ETL-ES-Harmony-WH11 eXtended dOwnrOd OPtiOn OPCión COn Varilla VertiCal MÁs larGa Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre- drilled set-screw hole.
-
Página 11: Blade Installation Instalación De Las Paletas
ETL-ES-Harmony-WH11 Blade installatiOn instalaCión de las Paletas Install the blade (2) to the short blade bracket (3), as shown, with blade screws (1) provided in the hardware bag. Install the long blade bracket (4) to the middle of the blade, as shown, using blade screws (1) provided in the hardware bag. - Página 12 ETL-ES-Harmony-WH11 MOuntinG MOntaje Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
-
Página 13: Wiring Options
ETL-ES-Harmony-WH11 wirinG OPtiOns OPCión de CaBleadO Pull CHain wirinG OPtiOn wall COntrOl wirinG OPtiOn Follow diagram above to make wiring connections for fan pull chain control. Follow diagram above to make wiring connections for wall control operation. OPCión de CaBleadO Para COntrOl de Pared OPCión de CaBleadO Para Cadenilla de tirO... - Página 14 ETL-ES-Harmony-WH11 seCure tO CeilinG aseGure el VentiladOr al CielOrrasO Align the keyholes on the canopy (3) with the protruding screw heads (2) from the mounting bracket (1). Lift the canopy up and rotate clockwise until the screwheads engage the keyslots fully.
- Página 15 ETL-ES-Harmony-WH11 liGHt fiXture installatiOn instalaCión del artefaCtO luMinOsO Install the mounting ring (1) onto the motor housing by using the screws (2) provided Remove the screw (1) located opposite the cutout in the mounting ring, and loosen (do in the hardware bag.
- Página 16 ETL-ES-Harmony-WH11 liGHt fiXture installatiOn instalaCión del artefaCtO luMinOsO Raise the light kit (1) up, and attach the light kit to the mounting ring by placing the keyslot holes from the light kit onto the two protruding screw heads from the mounting ring.
- Página 17 ETL-ES-Harmony-WH11 Locate the indentations on the neck of the glass (2) Install 2 x 40W type B bulbs (included). and align with the protrusions from the light kit (1). Lift the glass up allowing the protrusions to engage the Instale 2 bombillas tipo B (incluido) de 40 W.
- Página 18 ETL-ES-Harmony-WH11...
-
Página 19: Operation And Maintenance
ETL-ES-Harmony-WH11 OPeratiOn and MaintenanCe Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. -
Página 20: Operación Y Mantenimiento
ETL-ES-Harmony-WH11 OPeraCión y ManteniMientO FUNCIONAMIENTO Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 tirón – rápida; 2 tirones – mediana; 3 tirones – lenta; 4 tirones – apagado. -
Página 21: Troubleshooting Guide
ETL-ES-Harmony-WH11 If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some trOuBlesHOOtinG Guide cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting chart. -
Página 22: Guía Para Solucionar Problemas
ETL-ES-Harmony-WH11 Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación Guía Para sOluCiOnar PrOBleMas o cableado incorrectos. en algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experimenta alguna falla, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista autorizado y no intente reparar conexiones eléctricas. - Página 23 ETL-ES-Harmony-WH11...
- Página 24 Philadelphia, PA 19154 U.S.A. Philadelphia, PA 19154 U.S.A. Westinghouse Lighting Corporation, Westinghouse Lighting Corporation, titular de la licencia de Westinghouse Electric Corporation a Westinghouse Electric Corporation licensee es una marca registrada de is a registered trademark of Westinghouse Electric Corporation...