King gates MR2-K Características Técnicas página 3

DISPOSAL
As for the installation operations, even at the end of this product's
life span, the dismantling operations must be carried out by qualified
experts. This product is made up of various types of materials: some
can be recycled while others need to be disposed of. Find out about
the recycling or disposal systems envisaged by your local regulations
for this product category.
Important! – Parts of the product could contain pollutants or
hazardous substances which, if released into the environment,
could cause harmful effects to the environment itself as well as to
human health. As indicated by the symbol opposite, throwing away
this product as domestic waste is strictly forbidden. So dispose of it
as differentiated waste, in accordance with your local regulations,
or return the product to the retailer when you purchase a new
equivalent product.
Important! – the local applicable regulations may envisage
heavy sanctions in the event of illegal disposal of this product.
PRODUCT DESCRIPTION AND INTENDED USE
This receiver is part of the MR series by V2 SPA.
The receivers in this series are intended for use on V2 control units.
Any other use is improper and prohibited!
• Operates with STYLO4K series transmitters
• It is possible to store up to 500 different codes
• Memory full warning: the receiver blinks 15 times
• Self-learning of transmitters managed by radio
m
ATTENTION: Use the receiver MR2 only with V2
equipments
m
IMPORTANT: to memorize the code in the correct way
it is necessary to keep a minimum distance of 1,5 metres
between the transmitter and the receiver's antenna.
SELECTION OF THE RECEIVER CHANNEL
1.
Press P1 push-button of the receiver: L1 led switches on.
2. Release the push-button, the led switches off and it sends out a
sequence of single flashings for 5 seconds: the number of short
flashings shows the selected channel.
3. To select the further channels press and release the P1
push-button within 5 seconds, the led changes type of flashing
according to the following table:
SELECTED N°
CHANNEL IMPULSES P1
CHANNEL 1 1
CHANNEL 2 2
CHANNEL 3 3
CHANNEL 4 4
N° Flashing
1 2 3 4
•
•
•
•
PROGRAMMING OF THE MONOSTABLE
FUNCTION
1. Select the channel of the receiver to be programmed:
the led flashes
2. Within 5 seconds, press and hold the button on the remote
control: the receiver LED lights up for 1 second and then starts
flashing again
3. The code has been memorised and the receiver remains standby
for 5 s with a new code to be memorised
5. Memorise all the remote control units necessary
6. After 5 seconds without a valid transmission, the led is turned off
and the receiver returns to normal operating mode
REMOTE RADIO LEARNING
This procedure allows to memorize new transmitters by radio, in
sequence and without removing the receiver from the
installation.
The transmitter which allows to enable the programming by radio
must be memorized in advance.
The keys of all the transmitters saved in the memory via radio will
have the same logic as for those of the transmitter that enabled
programming.
Therefore, if the transmitter that activated programming
has key 1 saved only, the new transmitters can only be saved using
key 1.
1.
Press for at least 5 seconds the keys 1+2 or of one transmitter
that is already saved: led L1 flashes
2. Release both keys
3. Press, within 5 seconds, the key of the new transmitter that you
intend to save
4.
Release the key and repeat the procedure for the other keys of
the remote control or with other radio controls to be saved
CANCELLATION OF A SINGLE TRANSMITTER
1.
Turn off the power to the receiver
2. Holding down the P1 key, reactivate the power supply: LED L1
lights up steadily for a few seconds then starts flashing
3. During flashing, release the P1 key: LED L1 turns on steadily
4. Hold down a key of the transmitter that you want to delete: LED
L1 turns off and on again
5. Release the key: the transmitter has been deleted (all keys
memorized) and the receiver remains on hold for 5 sec. of
another transmitter to be deleted
6. After 5 seconds without any operation, the LED turns off and the
receiver returns to normal operation
NOTE: if you try to delete a transmitter that is not memorized,
the L1 LED flashes multiple times
TOTAL CANCELLATION OF TRANSMITTERS
1. Turn off the power to the receiver.
2.
Holding down the P1 key, reactivate the power supply: LED L1
lights up steadily for a few seconds then starts flashing
3.
Keep the button pressed until LED L1 remains on steady
4. Release the P1 key: the total cancellation is started and ends after
a few seconds when the LED goes out
3