Section 2: Unpacking; Section 3: Getting To Know Your Blender; Professional 750 - Blendtec PROFESSIONAL Serie Manual Del Propietario Y Guía Del Usuario

SECTION 2: UNPACKING

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• Professional series blender motor base
• Blender jar with lid
Additional literature may be included depending on package configuration�
1� Remove blender motor base, blender jar and lid from packaging�
2� Unwind the power cord�
3� Check for any packing material that may have blocked ventilation holes on the
underside of the blender motor base�
4� Inspect all items to ensure no damage occurred during shipment�
5� If any damage has occurred, contact Blendtec customer service (see page 17)
immediately�
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF
PURCHASE
Record your blender motor serial number and date of purchase in the space
below� You will need these when contacting Blendtec for service or questions�
Motor Serial No� (Found on bottom of motor base):_______________________
Date Of Purchase: _____________________________________________
Purchased From: ______________________________________________
2.3 REGISTERING
YOUR BLENDER
Register online at www�blendtec�com/registration

SECTION 3: GETTING TO KNOW YOUR BLENDER

(Refer to Figures 1 and 2 on Page 6)
3.1 BLENDER MOTOR BASE
• Smart Touch Interface: The interface consists of one-touch pre-programmed
cycles and speeds, as well as Stop and Pulse buttons�
• Hardened Metal Drive Socket: This is where the jar couples with the motor to turn
the blade assembly� It is made of hardened metal�
• LCD Information Centre: This displays how many blend cycles your blender has
run, remaining time during blends and any error messages�
• Power Unit: This unit is located within the blender motor base and contains the
computerised electronics that run the blender�
• Motor Base Cover: This durable plastic material houses the power unit�
• Power Cord: The power cord is located at the back of the motor base cover�
4
3.2 BLENDER JAR ASSEMBLY
The blender jar assembly consists of the blender jar, blade assembly and lid�
• Jar: The jar is durable, BPA-free and easy to clean�
• Blade Assembly: The uniquely designed stainless steel blade provides fast,
consistent blending�
• Lid: The lid seals liquids within the jar during blending�
NOTE: Filling the blender jar beyond the marked capacity is not recommended.
SECTION 4:
INSTALLATION & OPERATIONAL OVERVIEW

4.1 PROFESSIONAL 750™

4.1.1 INSTALLATION
Above Counter Installation
1� Place the blender on a flat, clean and dry surface� Blender vents should be
unobstructed to allow proper cooling during use�
2� Make sure an outlet is available within 61 cm (two feet) of the blender motor�
3� Place appropriately filled blender jar, with lid in place, onto blender base�
Preparation For In-Counter Installation
1� Identify the best place to install your blender� Consider proximity to ingredients,
available counter space and access to a power outlet�
2� Ensure that the location meets all dimensional requirements (see Figure 3)�
a� The countertop must be no thicker than 32 mm (1 1/4 inch) to ensure
adequate ventilation�
NOTE: Ensure sufficient air circulation beneath the blender base. Hot air should
not be trapped beneath the counter top. Nothing should be stored within 76 mm
(3 inches) of the bottom of the motor.
3� Cut a hole in the counter top 111 mm (4 ⅜ inches) wide and 149 mm (5 ⅞
inches) long with the shorter side facing the operator (See Countertop Hole
Template or Figure 3)� Make sure all space requirements and measurements are
correct BEFORE cutting� It is recommended that you consult with a professional
before cutting�
In-Counter Installation
1� Remove the motor base from the motor base cover�
2� Slide the blender base into the new hole in your countertop, with the LCD indicator
and touchpad facing the operator side of the blender� The rubber gasket on the
rim of the motor base should fit into the hole and rest lightly on the countertop�
3� Make sure the power switch is off� Plug the unit into a 220-240 volt outlet with
10 amp protection�
5