Maintenance And Storage - YATO YT-30432 Manual De Instrucciones

GB
Charging the rechargeable battery (VI)
In order to charge the rechargeable battery, remove it from the battery compartment. Connect the rechargeable battery charging
cable adapter to the power supply plug, then connect the rechargeable battery to the adapter plug, and connect the power supply
housing to the mains. The power supply housing is equipped with an LED. The red colour indicates charging, the green colour
indicates that the rechargeable battery is charged.
Warning! Disconnect the rechargeable battery from the power supply immediately after charging is complete. Leaving the re-
chargeable battery connected to the power supply for a long time will cause irreparable damage to the rechargeable battery.
Safety recommendations for battery loading
Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It
is prohibited to use a damaged loading dock and charger! For the purpose of loading batteries only the charging dock and the
charger provided may be used. Using another charger may be a cause of fi re or damage the tool. Batteries may be charged only
in a dry room, protected from unauthorised persons, particularly children. Do not use the charging dock and the charger without
permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required to disconnect the
charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange
smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket! The drill and automatic
return screwdriver is provided with an unloaded battery, so before work may commence, it is required to charge it following the
procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so called "memory eff ect", so
it is allowed to charge them at any moment. However, it is recommended to discharge them during normal work, and then load
them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it is required to do it at least
from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the electrodes, since this would
cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through
approximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the relative humidity of
50%. In order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of
prolonged storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this
would reduce its life and may cause irreversible damage. During storage, the battery will be gradually unloading due to leakage
conductance. The process of automatic unloading depends on the temperature of storage, since the higher the temperature, the
fastest the process. In case of incorrect storage of batteries, there is a danger of electrolyte leakage. In case of leakage, it is
required protect the leakage with neutralizing agent. In case of contact of electrolyte with the eyes, it is required to rinse the eyes
abundantly, and then immediately seek medical assistance. It is prohibited to use a tool with a damaged battery. In case the
battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Safety glasses
Included with the product are safety glasses which can help see the laser beam. Safety glasses do not provide protection against
laser radiation. Safety glasses do not provide protection against mechanical or thermal hazards. Safety glasses may distort col-
ours. Do not drive vehicles wearing these glasses.
Product use
If the product is used outdoors or in the presence of a strong light source such as sunlight, the working range and visibility of laser
lines may be reduced. An example of the product use is shown in fi gure (VII).

MAINTENANCE AND STORAGE

Having fi nished your work with the product, wipe it clean with a soft and slightly damp cloth. Next, wipe dry with a soft cloth or
leave to dry. Do not immerse the product in water. Do not clean with solvents, corrosive chemicals, alcohol, gasoline or abrasive
products (e.g. scouring cream). Store the product in a dry, well-ventilated indoor room, away from sunlight. The storage location
should not be accessible to children or anyone not authorized to operate the product. Other storage conditions should be as the
operating conditions. Remove the batteries before prolonged storage.
O R I G I N A L I N S T R U C T I O N S
12