Publicidad
Idiomas disponibles
Idiomas disponibles
5' & 6' Models: 3283ADJ60 & 3283ADJ72 Reference Chart
Gate Opening Horizontal Gate Frame Length
No Cutting Needed
72"
64"
Cut to 48" long
60"
Cut to 44" long
54"
Cut to 38" long
48"
Cut to 32" long
42"
Cut to 26" long
36"
Cut to 20" long
30"
Cut to 14" long
24"
Cut to 8" long
Minimum gate opening for 3283ADJ60 / 3283ADJ72 is 24"
For gate openings not represented by the tables, add 1" of horizontal gate
frames length for each additional inch of gate opening. For example if the
gate opening is 44", cut each horizontal gate frames to 28".
Step 3:
Assemble the gate frame using the vertical and horizontal gate frames.
Ensure the final assembly is square and correctly fits into the gate
opening, ensuring 2" exist between each side of the assembled gate
frame and the gate post opening. Install the self-tapping screws into
each corner of the gate frame using a screwdriver or nut driver.
Hinge Side
Step 4:
Install the truss wire. The top connection is the hinge side of the gate,
the bottom connection is the latch side of the gate. (Figure 2) Hook the
turnbuckle to the hinge side hole, and the hook to the latch side hole.
Use truss wire clamp to secure the latch side of the truss wire
(Figure 2). Tighten the truss wire using the turnbuckle. When
complete, trim off any excess wire.
Step 5:
Install the chain link fabric on the assembled gate frame. Thread the
tension bar through one side of the gate fabric and secure with the
gate clips. Roll the fabric out across the gate frame and pull taught.
LIMITED EXPRESS WARRANTY: Midwest Air Technologies, Inc. warrants your product to be free of defects in workmanship and further warrants that under normal use will be free
of problems for one full year from date of purchase by original purchaser. MIDWEST AIR TECHNOLOGIES, INC. WILL NOT HAVE OTHER OR GREATER LIABILITY FOR DEFECTS,
NOR WILL MIDWEST AIR TECHNOLOGIES, INC. HAVE ANY LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply to you. If you discover a defect in the product during the warranty period and wish to obtain
replacement parts or have questions, send notice of claim to: Midwest Air Technologies, Inc. 6700 Wildlife Way, Long Grove, IL 60047 Include your return address, a copy of
the original invoice or proof of purchase date, plus a description of claimed defect. All implied warranties of merchantability and fitness for particular purpose are limited to a duration
of one (1) year from date of purchase. Some states do not allow limitations on how long an implied warranty may last, so the above limitations may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which may vary from state to state.
Final Gate Dimension
68" wide
60" wide
56" wide
50" wide
44" wide
38" wide
32" wide
26" wide
20" wide
Figure 2
Latch Side
If the chain link fabric is too long, remove as many links as needed by
twisting one row counter clockwise to remove excess fabric. Thread
the second tension bar through the fabric and connect to the gate
frame using the gate clips (Figure 3). Install tie wires to secure the top
and bottom fabric to the gate frame. (Figure 3)
Step 6:
Hang the gate on the gate posts. Install the frame hinges on the hinge
side of the assembled gate frame. Install the fork latch on the latch
side of the gate frame (Figure 4). Set the post hinges (not included).
Set the gate onto the post hinges and tighten all nuts to secure in
place. The gate should freely open and close with little effort.
Gate Post
Post Hinge
Post Hinge
FOR DRIVE GATES
For drive gates, the size of each gate is calculated as follows: Measure
the opening between the gate posts. Subtract 6 inches. Divide that
number by 2. For example, the opening between the gates posts is 96
inches. 96-6 = 90. 90 ÷ 2 = 45. Each gate panel should be 45" wide.
Repeat Steps 3-6 above for the second adjustable gate.
NOTE: only one fork latch will be installed between the two
gates. Add the drive gate drop rod assembly (sold separately)
to the drive gate per the instructions provided with the drop rod
assembly.
Figure 3
Figure 4
Fork Latch
Page: 2 of 4
Publicidad
