Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Attaching Woolen Wax Applicator Bonnet
(Fig. D, E, G)
WARNING: If any parts are missing, DO NOT
operate this buffer/polisher until the missing
parts are replaced. Failure to do so could result in
possible serious personal injury.
1. Attach the wax applicator bonnet
base
3
as shown in Fig. D. ALWAYS make sure the elastic
strip on the bottom of the bonnet is securely tucked on
the underside of the foam pad.
2. For paste wax, use a putty knife or any other flat object,
apply paste wax to the bonnet by spreading a teaspoon
of wax evenly over the entire surface of the wax
applicator bonnet as shown in Fig. E.
iMPORTAnT: Do not apply wax directly on vehicle.
3. For liquid wax, apply three swirls of wax over applicator
bonnet. This should be enough to cover 1/4 of vehicle
surface as shown in Fig. G.
4. For the second, third, and fourth applications, only
use about one half as much as on first application.
The bonnet will not absorb as much wax on
these applications.
Attaching Terry Cloth Polishing Bonnet
(Fig. F, G)
1. Place the terry bonnet
2. ALWAYS make sure that the elastic strip on the bottom
of the bonnet is securely tucked on the underside of the
foam pad.
3. Apply wax in a circular motion as shown in Fig. G.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. H)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
10
8
to the foam pad
9
on foam pad
3
.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
6
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Speed Dial (Fig. A)
The speed dial
4
changes the speed of the polisher.
Rotate the dial forward to increase the speed or backward
to decrease the speed. 1 is the lowest setting and 3 is the
highest setting.
Proper Hand Position (Fig. I)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires both hands on the
perimeter handle
1
.
Waxing Vehicle (Fig. J)
1. Before you begin to wax, buff, and polish your vehicle,
remove all road tar, excess grease spots and bug stains
with a general‑purpose cleaner. Dry your vehicle.
2. Place buffer/polisher against vehicle and turn buffer/
polisher ON by sliding switch to On position. To avoid
splashing wax, ALWAYS start and stop the buffer/polisher
against the surface to be polished.
3. Begin buffing at a low speed and then turn up the speed
using the speed dial
4. Apply wax in a straight line with either a side‑to‑side or
back and forth motion. ALWAYS use broad, even strokes
when applying wax. Apply wax in a thin, even coat. Too
much wax does not add any more protection and only
makes the wax removal more difficult.
5. Apply wax to the flat surfaces (hood, trunk and roof ) first.
Wax one section at a time.
6. After flat surfaces are covered, wax the sides. It is
easiest to apply the wax to the entire surface before
starting the removal phase; however, follow the specific
recommendations of the wax or polish being used.
7. When you have finished applying wax with the
applicator, bonnet, SHUT OFF the buffer/polisher before
removing from the vehicle's surface.
nOTE: DO NOT apply too much wax to the bonnet. Applying
too much wax causes the bonnet to become saturated and it
will not last as long. THIS MAKES POLISHING MORE DIFFICULT
AND IT TAKES LONGER.
nOTE: If the bonnet is continually coming off the pad, you
may be using too much wax.
nOTE: If buffing seems difficult, you have used too
much wax.
iMPORTAnT: DO NOT apply excessive pressure against
the work surface with this tool. The random orbital motion
5
into the tool handle, align the
4
.
Publicidad
Tabla de contenido
