Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING: This tool is not intended for use in
potentially explosive atmospheres and is not insulated
from coming into contact with electrical power.
•
Use the pneumatic tool only for the purpose for which it
was designed.
•
Do not use the tool as a hammer.
•
Always carry the tool by the handle with hand off
both triggers.
•
Never lift, pull, lower, or carry the tool by the air hose.
•
Whipping hoses can cause severe injury. Always check for
damaged or loose hoses or fittings.
•
Never direct compressed air at yourself or anyone else.
•
Compressed air can cause severe injury.
•
Do not alter or modify this tool from the original design or
function without approval from CRAFTSMAN.
•
Never clamp or tape the trigger in an actuated position.
•
Ensure tool is always safely engaged on the workpiece and
cannot slip.
•
Never leave a tool unattended with the air hose attached.
TO PREVENT ACCIDENTAL INJURIES:
•
Never place a hand or any other part of the body in fastener
discharge area of tool while the air supply is connected.
•
Never actuate the tool unless nose is directed at the work.
•
Do not actuate the tool while loading.
•
Keep hands and body parts away from the discharge
area of the tool. While in use NEVER grasp the tool by the
magazine or canister, a mis‑driven fastener can exit the
nose causing injury.
Additional Safety Information
WARNING: Never modify the power tool or any part of
it. Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•
lead from lead‑based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
•
Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
Use clamps or other practical ways to secure and
•
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
BPM .................... beats per minute
V ......................... volts
min ..................... minutes
j
or DC ............ direct current
.../min .............. per minute
RPM .................... revolutions per
minute
A ......................... amperes
Hz ....................... hertz
W ........................ watts
Wh ...................... watt hours
n o ....................... no load speed
n ......................... rated speed
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental actuation
can cause injury.
TOOL SPECIFICATIONS
Height (inch/meter)
Width (inch/meter)
Length (inch/meter)
Weight (lbs/kg)
Recommended Operating Pressure
Air Consumption per 100 cycles
Loading capacity
Lubrication
English
c
..................... safety alert symbol
h
..................... wear respiratory
protection
f
..................... wear eye protection
i
..................... Class II Construction
(double insulated)
g
..................... wear hearing
protection
a
..................... read all
documentation
n
..................... avoid staring at
light
l
or AC............ alternating current
Ah ....................... amp hours
6.3/0.16
1.7/0.04
8.9/0.22
2/0.91
60‑100 psi (4.1 to 6.9 bar)
1.56 SCF
170 nails
Oil
5
Publicidad
Tabla de contenido
