Primus 2213 Manual De Instrucciones

2213
ID: 2531CT-0140
Design and Quality Primus AB Sweden
Tel: +46 8 564 842 30
Fig 1
2
Fig 2
Fig 3
ENG
-2531-20
IMPORTANT: Read these instructions carefully and fami-
liarize yourself with the product before fitting the appliance
to the gas cartridge. Review the instructions periodically to
stay familiar with how the appliance functions. Retain these
instructions for future reference.
CAUTION: Only for outdoor use.This gas appliance consu-
mes oxygen. Do not use this appliance anywhere except
outdoors to avoid endangering your life.
1. INTRODUCTION
1.1 This appliance shall be used exclusively with
Primus Propane/Butane mix cartridges 2202
and 2207.
1.2 It may be hazardous to attempt to fit other types of
gas cartridges.
1.3 Gas consumption: 25 g/h/ 0,9 oz/h / ca. 0,3 kW
butane at 1 bar pressure.
1.4 Jet nipple size: 0,12 mm, 732070 Butane
1.5 This appliance complies with EN 521/ Z21.73-
2000/CSA 11.1-2000
2. SAFETY INFORMATION (Fig 1)
2.1 Ensure that the appliance seals (1) are in place and
in good condition before fitting the gas cartridge.
2.2 This appliance is only for outdoor use!
2.3 The appliance must be operated on a level surfa-
1
ce.
2.4 Make sure that no flammable materials are near the
gas appliance, see section 5.6
2.5 Always change or fit the gas cartridge in a safe
place, only outdoors, away from other people and
away from any possible source of ignition such as
open flames, pilot flames, or electrical sparks.
2.6 If you have to check the gas seals of the applian-
ce, do so outdoors. Do not check for leaks with an
open flame. Use soapy water or the like.
2.7 Never use an appliance with damaged or worn
seals and never use a leaking, damaged or
malfunctioning appliance.
2.8 Never leave the appliance unattended when lit.
2.9 Avoid flaring up,by being careful when moving
the appliance. This is very important when a new
cartrige is used.
3 HANDLING THE APPLIANCE
3.1 Be careful not to touch hot parts of the appliance
during or after use.
3.2 Storage: Always unscrew the cartridge from the
appliance when not in use. Store them in a
safe dry place away from heat.
3.3 Do not misuse the appliance, or use it for anything
for which it has not been designed.
3.4 Handle the appliance with care. Do not drop it.
4. ASSEMBLING THE APPLIANCE (fig.2)
4.1 Ensure that the control knob (2) is turned off
(turned fully clockwise).
4.2 Keep the cartridge (3) upright when fitting it to the
valve.
4.3 Place the valve squarely on top of the cartridge (as
shown in fig .2).
4.4 Gently screw the cartridge into the valve until it
meets the O-ring of the valve. Be careful not to fit
the cartridge cross threaded. Screw handtight
only. Do not overtighten to avoid damaging
the cartridge valve.
4.5 Ensure that a complete gas seal has been made. If
you have to check the gas seals of the appliance,
do so outdoors. Do not check for leaks with an
open flame. Use soapy water or the like, applied
to the joints and connections of the appliance.
Any leakage will show up as bubbles around the
leakage area. If you are in doubt or you can hear
or smell gas, do not attempt to light the appliance.
Unscrew the cartridge and contact your local
dealer.
4.6 Pre-burning the mantle before use: Remove the
mesh basket (4) by turning it counter-clockwise
and lifting it up. Place the large hole of the mantle
(6) on the lower grooves (7) at the burner tube (5),
then convey the igniter electrode tip smoothly to
the inside of the mantle. Finally place the small hole
of the mantle on the upper groove on the burner
tube(5). Make sure that the mantle is uniformly
threaded around the whole burner tube. Light the
mantle with a match or lighter and let it burn until
there is only a white "skeleton" left.
4.7 When the mantle has been fully pre-burnt turn
on the control knob (2) and ignite the burner by
pushing the trigger (8) downwards. Keep it burning
at full power for about 30 seconds. Turn the lantern
off and then replace the lantern mesh basket (4)
and turn it clockwise until a click is heard.
51574/3
2213 PRIMUS MICRON LANTERN
INSTUCTIONS FOR USE
4.8 The lantern is now ready for use.
NOTE: When the mantle has been burned off, it is
very brittle and care should be taken not
to damage it. A damaged mantle will cause bad
combustion and also lower the light output from
the lantern. Spare mantles are available from your
local dealer.
5. OPERATING THE APPLIANCE
5.1 Always operate the appliance on a firm, level
surface.
5.2 Turn the knob counter-clockwise (2) and light the
burner (5) immediately by pushing the trigger (8)
downwards. If the burner does not ignite, push the
trigger several times until it ignites.
5.3 Adjust the size of the flame by turning the control
knob (2).
5.4 After lighting, operate the appliance upright and do
not move it around. Flaring may occur if
the appliance has not fully warmed, or if it is moved
carelessly.
5.5 After use, ensure that the valve is fully shut (control
knob turned fully clockwise).
5.6 Suspension cable for transport. When suspending
the lantern from the ceiling or the like, make sure
that the distance to combustible material
is at least 500 mm. OTHERWISE a fire may
break out.
6. CHANGING THE CARTRIDGE
6.1 Shut the valve fully. Be sure the flame is extinguis-
hed and no other flame is nearby. Take the unit
outdoors, and away from other people. Unscrew
the cartridge from the valve and replace the old
cartridge with a new Primus cartridge. Always
check the O-ring in the appliance. If it is cracked
or worn, replace it. Apply the valve thread squarely
to the cartridge and screw it hand tight only as
decribed in section 4. Avoid cross threading.
7. MAINTENANCE
7.1 If gas pressure drops or the LP- gas will not light,
check if there is gas left in the cartridge (3). If so,
the jet nipple (9) might be blocked.
7.2 Cleaning the jet nipple. Fully turn off the control
knob (2) and unscrew the cartridge (3).
7.3 Unscrew the two small screws (10) at the side of
the lantern and lift the lantern part (11) smoothly
from the valve body.
7.4 Unscrew the jet nipple (9) from the valve using a 6
mm spanner.
7.5 Clean out the jet nipple by blowing through the tiny
hole at the front. Do not use an incorrect
size needle or any type of pin etc. to clean the
blockage or you may damage the hole and
make the appliance unsafe.
7.6 Re-fit the jet nipple and screw it tightly to ensure
a gas seal. Re-fit the cartridge by following the
description in section 4. For extra safety, check the
joint with warm soapy water. If bubbles appear, the
joint is not tight enough.
7.7 Push the lantern part (11) to the valve body and
secure with the two small screws (10).
8. ROUTINE SERVICE AND MAINTENANCE
8.1 Always ensure that the O-ring sealing is in place
and in good condition. Always check this
each time prior to fitting the appliance. Replace the
O-ring if it is damaged or worn.
8.2 New sealing O-rings are available from your local
dealer.
9. SERVICE AND REPAIR
9.1 If you cannot rectify any fault by following these
instructions, return the appliance to your local
dealer.
9.2 Never attempt any other maintenance or repair.
9.3 Never modify the appliance. This may cause the
appliance to become unsafe.
10. SPARES AND ACCESSORIES
10.1 Use only Primus branded spares and access-
ories. Be careful when fitting spares and
accessories. Avoid touching hot parts.
10.2 Replacement Cartridges: Use only Primus 2202,
2207 Propane/Butane mix gas
with this appliance.
10.3 Spare parts
732070 Jet nipple 0,12 mm
732440 O-ring
732460 Piezo igniter
730800 Mantle
732450 Mesh basket
10.4 In case of difficulties in obtaining spare parts or
accessories,consult the distributor in your country.
Visit www.primus.se
cartridges
1