EN
User Manual
4-way socket cube with switch and 2 USB ports
1
Safety instructions
The user manual is part of the product and contains important information for correct use.
• Read the user manual completely and carefully before use.
The user manual must be available for uncertainties and passing the product.
• Keep this user manual.
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.
• Do not insert objects into air vents or sockets!
• Keep enough space around product and to the whole system to ensure proper ventilation and mobility.
Voltage-free only when the plug is pulled out.
• In case of emergency, after use and during thunderstorms, disconnect the power plug from the socket
directly at the plug housing.
Kinked connection cables increase the risk of electric shock.
• Always unwind the connection cable completely.
A defective device must not be put into operation, but must be secured against unintentional further use.
• Only use the product, product parts and accessories if they are in perfect condition.
• Avoid extreme loads such as heat and cold, wetness and direct sunlight, microwaves as well as vibrat-
ions and mechanical pressure.
• In case of questions, defects, mechanical damage, malfunctions and other problems that cannot be sol-
ved by the accompanying documentation, contact the dealer or manufacturer.
• Installation, disassembly, maintenance and repair work may only be carried out by qualified electrical
specialists.
• Compare technical data of product, power supply and peripheral devices. They must be identical.
• Use only in dry conditions.
• Do not plug in one after the other.
• Never touch the power plug with wet hands.
• Do not operate covered.
• Do not operate in potentially explosive atmospheres.
Risk of injury from tripping and falling.
• Make sure that the connection cable is laid in such a way that it does not obstruct anyone and is not da-
maged.
• Install the product in such a way that no persons or things can be injured or damaged, e.g. by falling,
tripping or similar.
Do not overload the power strip.
• Observe the max. permissible load capacity in the "Specifications" chapter.
Not suitable for children. The product is not a toy!
• Secure packaging, small parts and insulating material against accidental use.
2
Description and function
2.1
Product
The product is a 4-way socket cube with 2 additional USB ports for charging and powering small mobile de-
vices with USB connection and extension cord for home use.
○ With illuminated ON/OFF switch
○ With fixtures for wall mounting for attachment to the wall
2.2
Scope of delivery
4-fold socket cube with switch and 2 USB ports, User Manual
2.3
Operating Elements
1 Protective contact sockets
2 Hybrid connector
3 USB 2.0 charging ports
4 Overvoltage protection indicator
2.4
Specifications
Article number
Connection type 1
Connection type 2
Connection type 3
Power cord type
Rated voltage / current
Max. permissible load capacity
Output voltage USB 2.0
Overvoltage protection
Average active efficiency
Efficiency at low load (10 %)
No-load power consumption
Weight
Dimensions (LxWxH)
Mains cable length
Protection class
Protection level
REV2022-03-17
V1.1aw
Subject to change without notice.
5 Ventilation grille
6 ON/OFF switch for all sockets
7 Devices for wall mounting
41268
4x Protective contact socket (Typ F, CEE 7/3)
2x USB 2.0 Charge port (Typ A)
1x Hybrid connector (Typ E + F, CEE 7/7)
H05-VV-F 3G 1.5 mm²
250 V
, 50 Hz, 16 A max.
3680 W
2x 5.0 V
, @ 2.1 A max. total, 10.5 W
TYP3, Uc = 255 V
, 50 Hz,
Uoc = 6.0 kV (L-N, L/N-PE),
Up= 2.5 kV (L-N) / 2.0 kV (L/N-PE)
80.9 %
77.7 %
0.04 W
471 g
90 x 90 x 89 mm
1.5 m
I
IP20
3
Intended use
We do not permit using the device in other ways like described in chapter "Description and
Function" or in the "Safety Instructions". Use the product only in dry interior rooms. Not attending
to these regulations and safety instructions might cause fatal accidents, injuries, and damages
to persons and property.
IP20: This product is protected against medium sized foreign objects, but not against water ingress.
4
Preparation
1. Check the scope of delivery for completeness and integrity.
2. Compare the specifications of all used devices and ensure compatibility.
5
Set up / mounting
5.1
Set up
• Place the socket cube on an easily accessible, stable and horizontal surface.
5.2
Wall mounting
If required, the socket cube can also be mounted horizontally on the wall.
Mounting material is not included.
1. Select suitable mounting material according to the selected surface and product weight.
2. Mark the drill hole distance of 54 mm (see illustration in chapter 2.3) using a suitable pen.
3. Drill the mounting holes using a suitable tool.
4. Fasten the socket cube.
6
Connection and operation
1. Connect your household appliances to socket cube.
2. Connect up to 2 small mobile devices with USB ports to the USB 2.0 charging ports of the socket cube.
Use the USB 2.0 charging ports only for IT or I.T.E devices.
3. Connect the socket cube to an easily accessible grounded socket.
4. Turn on the socket cube by pressing the ON/OFF switch (6).
An audible "click" sound is heard and the ON/OFF switch (6) lights up red.
The overvoltage protection is active when the overvoltage protection indicator (4) lights up.
The overvoltage protection indicator (4) lights up as soon as voltage is present.
5. Disconnect all cable connections after use or turn off the ON/OFF switch (6) by pressing it.
The ON/OFF switch (6) is no longer lit.
7
Maintenance, Care, Storage and Transportation
The product is maintenance-free.
NOTICE!
Material damage
• Disconnect the power plug from the socket before each cleaning.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a dry and dust-protected ambiece when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
8
Disposal instructions
According to the European WEEE directive, electrical and electronic equipment must not be
disposed with consumers waste. Its components must be recycled or disposed apart from each
other. Otherwise contaminative and hazardous substances can damage the health and pollute the
environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the producer, the
dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in
national right. The symbol on the product, in the user manual, or at the packaging alludes to these terms.
With this kind of waste separation, application, and waste disposal of used devices you achieve an important
share to environmental protection.
WEEE No: 82898622
9
EU Declaration of conformity
With the CE sign Goobay®, a registered trademark of the Wentronic GmbH ensures, that the
product is conformed to the basic European standards and directives.
10
Symbols used
For indoor use only
Alternating current
Direct current
Protective earth; protective ground (Class I equipment)
- 2 -
IEC 60417- 5957
IEC 60417- 5032
IEC 60417- 5031
IEC 60417- 5019
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
41268
Goobay®