Publicidad
Idiomas disponibles
Idiomas disponibles
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the Sure Fit
®
nozzle.
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, Sure Fit
®
nozzle and nozzle adapter in the storage
groove.
120 VOLT AC POWER OUTLET
Rated Versus Actual Current Draw of Equipment
Most electrical tools, appliances, electronic devices and audio/visual equipment
have labels that indicate the power consumption in amps or watts. Be sure that the
power consumption of the item to be operated is below 200 watts. If the power
consumption is rated in amps AC, simply multiply by the AC volts (120) to determine
the wattage.
Resistive loads are the easiest for this unit to run; however, it will not run larger
resistive loads (such as electric stoves and heaters), which require far more wattage
than the unit can deliver on a continuous basis. Inductive loads (such as TVs and
stereos) require more current to operate than do resistive loads of the same
wattage rating.
Power Inverter Output Waveform
The AC output waveform of this unit is known as a modified sine wave. It is a stepped
waveform that has characteristics similar to the sine wave shape of utility power. This
type of waveform is suitable for most AC loads, including linear and switching power
supplies used in electronic equipment, transformers, and small motors.
Protective Features
The unit monitors the following conditions:
Low internal battery voltage: The unit will automatically shut down when the
battery voltage drops too low, as this can harm the battery.
High internal battery voltage: The unit will automatically shut down when the
battery voltage is too high, as this can harm the unit.
Thermal shutdown protection: The unit will automatically shut down when the
unit becomes overheated.
Overload/short circuit protection: The unit will automatically shut down when
an overload or short circuit occurs.
IMPORTANT
When the AC Power Outlet is in use, the unit will monitor for the following fault
conditions: thermal fault, low and high battery voltage fault, overload and short
circuit.
1. If a low internal battery voltage fault condition exists, the AC Power Outlet will
shut down automatically and the backlit LCD screen will display the following
until the fault is corrected:
The Digital Display will show "AC"; the EMPTY Battery Status Icon and Fault
Icon on the LCD Screen will flash.
2. If a high internal battery voltage fault condition exists, the AC Power Outlet
will shut down automatically and the backlit LCD screen will display the
following until the fault is corrected:
The Digital Display will show "AC"; the FULL Battery Status Icon and Fault Icon
on the LCD Screen will flash.
PPS200S_ManualENSP_072621.indd 10-11
PPS200S_ManualENSP_072621.indd 10-11
3. If a thermal, overload or short circuit fault condition exists, the AC Power
Outlet will shut down automatically and the backlit LCD screen will display the
following until the fault is corrected:
The Battery Status Icon will light solid; the "AC" on the Digital Display and the
Fault Icon on the LCD Screen will flash.
Should any of the above fault conditions occur:
1. Disconnect the appliance from the unit.
2. Press the AC Power Button to turn the AC Power Outlet off.
3. Make sure the unit does not need to be recharged.
4. Allow the unit to cool down for several minutes.
5. Make sure the rating of the appliance plugged into the unit is 200 watts or
lower and that the appliance cord and plug are not damaged.
6. Assure there is adequate ventilation around the unit before proceeding.
Using the 120 Volt AC Outlet
1. Press the AC Power Button to turn on the 120V AC Power Outlet. Refer to the
"Features" section to locate. A beep will sound and the LCD Screen will display
the following:
The Battery Status Icon lights solid and the Digital Display shows "AC,"
indicating the AC outlet is ready to use.
2. Lift up the cover of the unit's 120 volt AC outlet.
3. Insert the 120 volt AC plug from the appliance into the 120 volt AC outlet.
4. Press the AC Power Button again to turn off the 120V AC Power Outlet.
Monitor the unit's internal battery status on the LCD Screen. Four solid bars in the
battery icon indicates a full battery. When the battery level is nearly empty with
only one solid bar, the unit MUST be recharged at this time.
IMPORTANT: Make sure the AC Power Outlet is turned off when the unit is being
recharged or stored.
USB PORTS
The USB Power Button and the two USB Ports are located on the front of the unit;
the USB Power/Fault Indicator is a translucent ring around each of the USB Ports.
Refer to the "Features" section to locate.
IMPORTANT NOTES
1. The two USB Ports provide a total of 3.1A (5V each).
2. When the USB Ports are in use, the unit will monitor for the following USB
fault conditions on both USB Ports: low battery voltage fault, overload and
short circuit. If a fault condition exists in either of the USB Ports, the USB
Power/Fault Indicators will flash blue. In any of these cases, the backlit LCD
screen will continuously display the following:
The Fault Icon will flash. The USB Ports will automatically shut down. Should
this occur:
a. Disconnect the USB-powered device and press the USB Power Button
again to turn off the USB Ports immediately.
b. Make sure the unit does not need to be recharged.
10
c. Allow the unit to cool down for several minutes before attempting to use
the USB Ports again.
d. If an individual USB device is within specifications and the fault occurs,
have the USB device checked for malfunction and do not continue to use
it with these USB Ports.
3. This unit's USB Ports do not support data communication. They only provide
power to external USB-powered devices.
4. Some household USB-powered electronics will not operate with this unit.
Using the USB Ports
1. Press the USB Power Button to turn on both USB Ports. A beep will sound, the
USB Power/Fault Indicators around each of the USB Ports will light blue and the
LCD screen will continuously display the following:
The Battery Status Icon and Battery Voltage Indicator will light solid, as well as
the USB Icon, indicating the USB ports are ready to use.
2. Plug the USB-powered device into the USB power port(s) and operate normally.
3. Press the USB Power Button again to turn off the USB Ports.
Periodically check the unit's battery status on the backlit LCD screen. Four solid bars
in the battery icon indicates a full battery. When the battery level is nearly empty
with only one solid bar or completely empty with 4 empty bars, the unit must be
recharged at this time or the unit's built-in low voltage protection will activate. The
empty Battery Status Icon will flash for a short period of time before automatic
shut down.
IMPORTANT: Make sure the USB Ports are turned off when the unit is being
recharged or stored.
LED AREA LIGHT
The built-in LED Area Light is controlled by the area light on/off button on the
control panel. Refer to the "Features" section to locate.
1. Press the Area Light Power Button once to turn the light on.
2. Press the Area Light Power Button again to turn the area light off.
When the Area Light Power Button is pressed to turn it on, a beep will sound. The
backlit LCD screen will turn on for 10 seconds (only) and will then continuously
display the Battery Status Icon and the Battery Voltage Indicator.
Periodically check the unit's battery status on the backlit LCD screen. Four solid bars
in the battery icon indicates a full battery. When the battery level is nearly empty
with only one solid bar or completely empty with 4 empty bars, the unit must be
recharged at this time or the unit's built-in low voltage protection will activate. The
empty Battery Status Icon will flash for a short period of time before automatic
shut down.
IMPORTANT: Make sure the Area Light is turned off when the unit is being
recharged or stored.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is
charged at least every 30 days.
From time to time wipe the outside of the appliance with a soft cloth. Do not
immerse the appliance in water.
There are no user-replaceable parts. Periodically inspect the condition of adapters,
connectors and wires. Contact manufacturer to replace any components that have
become worn or broken.
Battery
Please be advised that the battery is designed to last the service life of
the unit and is not replaceable, removable or serviceable. Service life is
dependent on a number of factors including but not limited to the number of
recharge cycles, and proper care and maintenance of the battery by the end user.
Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid
battery, which must be disposed of properly. Recycling is
required. Failure to comply with local, state and federal
regulations can result in fines, or imprisonment.
Please recycle.
WARNING:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
TROUBLESHOOTING
Unit Not Charging
• Make sure all of the unit's functions are turned off.
• Check the connection to the AC power source.
• Confirm there is a functioning AC current.
Engine fails to jump-start
• Make sure a proper polarity cable connection has been established.
• The unit may be overheated due to the excessive engine cranking. Make sure all
the unit functions are turned off and allow the unit to cool down before resuming
operation.
• Make sure the unit is not being operated in the compressor mode.
• Check that the unit has a full charge. Recharge the unit if necessary.
Portable Compressor will not inflate
• Make sure the Compressor Power Button has been pressed to turn the compressor
on.
• Make sure the unit is not being operated in the Jump-Starter mode.
• Make sure the Sure Fit
nozzle is securely screwed on to the valve stem when
®
attempting to inflate tires; or that the nozzle adapter is securely screwed into the
Sure Fit
nozzle and is inserted properly into the item to be inflated on all other
®
inflatables.
• Check that the unit has a full charge. Recharge the unit if necessary.
120 volt AC outlet will not power appliance
• Make sure the AC Power Button has been turned on.
• Make sure you have followed all the steps in the "120 AC Power Outlet" section
carefully. Refer to the important notes included in that section that explain
common problems and solutions.
• Make sure the combined draw of the appliance being powered is not more than
200 watts.
• Check that unit has a full charge. Recharge unit if necessary.
USB power port will not power appliance
• Make sure the USB Power Button is in the on position.
• Make sure all the USB Power/Fault Indicators light solid blue. If a fault condition
exists in either of the USB Ports, the USB Power/Fault Indicators will flash blue.
Refer to the Important Notes in the "USB Ports" section to remedy any faults.
• Make sure that the total draw of all USB devices plugged into the two USB Ports
does not exceed 3.1A.
• Some USB-powered household electronics will not operate with this USB charging/
power port. Check the manual of the corresponding electronic device to confirm
that it can be used with this type of USB charging/power port.
• Check that the unit has a full charge. Recharge the unit if necessary.
LED Area Light does not come on
• Make sure the Area Light Power Button is in the on position
• Check that the unit has a full charge. Recharge the unit if necessary.
ACCESSORIES
Recommended accessories for use with your tool may be available from the
manufacturer. If you need assistance regarding accessories, please contact the
manufacturer at 1-877-571-2391.
The use of any accessory not recommended for use with this appliance could be
hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the manufacturer at 1-877-571-2391.
11
7/26/2021 9:44:20 AM
7/26/2021 9:44:20 AM
Publicidad
