Initial Operation; Battery Pack - Metabo BSA 18 LED 5000 DUO-S Manual Original

en ENGLISH
1 Feet
2 Locking mechanism for feet
3 Battery pack release button

4 Battery pack *

5 Capacity and signal indicator
6 Capacity indicator button
7 Carry handle
8 Snap lock for feet
9 Clamping lever for height adjustment at the
bottom
10 Telescopic rod
11 Clamping lever for height adjustment at the top
12 Switch
13 Lamps head
14 Magnets to fix the lamps heads
15 Lamps head handle
16 Adjusting screw
* equipment-specific
3. Setup
See figures on page 2
1. Loosen the snap locks (8) from the feet (1),
unfold and let them engage.
2. For a more stable stand and if necessary, the
adjusting screws (16) can be unscrewed from
the foot ends (1) (see fig. A (d) p. 2) using a
suitable tool and screwed back in the other way
around with the tip pointing outwards.
Use only on suitable and scratch-resistant
underground!
3. If necessary, open the lower (9) and/or upper
clamping lever (11) and set telescopic tube (10)
to the desired height and then lock again the
clamping levers (9) and (11).
4. Undo the magnetic lock (14) by pulling the
handles (15) of the lamps heads (13) apart and
then pull the lamps heads apart.
5. Adjust the swivelling lamps heads (13) as
required.
Do not turn the lamps heads excessively

4. Initial operation

4.1 Battery pack
Charge the battery pack (4) before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Battery packs with capacity and signal indicator (5)
(depends on the design variant):
- Press the button (6), the LEDs indicate the charge
level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
8
4.2 Inserting and removing the battery pack
See fig.p. 2
Inserting:
Slide in the battery pack (4) until it engages.
Removing:
Press the battery pack release (3) button and
remove the battery pack (4).
The ideal storage temperature for battery packs is
between 10°C and 30°C.
4.3 Switching on/off, setting the light
intensity
Do not direct the light beam into the eyes of
people or animals.
CAUTION Do not stare at operating lamp.
1.Turn on and off at the switch (12).
2. Adjust the luminosity by turning the switch (12)
to position I or II.
5. Dismantling
See figures on page 2
Remove the battery pack (4) before
dismantling.
1. Put the lamps heads (13) in a horizontal position
with the beam direction upwards and fold them
until the magnets (14) fix them together.
2.
Caution, risk of crushing! Hold the telescopic
tube (10) above the clamping levers (9) and
(11), before opening a clamping lever!
(see fig. A (a) p. 2)
Open the lower (9) and/or upper clamping lever
(11) and push the telescopic tubes (10) into
each other in a controlled manner. Correctly
close the clamping levers again to avoid
uncontrolled slipping apart.
3. If the adjusting screws (16) were mounted,
unscrew them again and screw them back in the
other way around (see fig. A (d) p. 2). Use
suitable tools to lower them completely into the
stand.
4. To undo the feet, release one foot and push the
lock (2) of the foot downwards (see fig. A (c) p.
2) and fold the released foot upwards (see fig. A
(b) p. 2) until it engages at the snap lock (8).
Subsequently, lay the device flat and assemble
the other feet in the same manner.
6. Transport
Remove the battery pack (4) before any
transport.
The device is transported in assembled state
according to chapters 3 and 5 as shown on page 2
in fig. B.
The carry handle (7) is suited exclusively for
carrying the device.
Secure the device against shocks during transport.