Maintenance And Inspection - HIKOKI DS 18DDQ Instrucciones De Manejo

English
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3 seconds
to confi rm that the battery being charged with charger
is taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Names of parts*
1
Removing and inserting the battery
Charging
Adapter removal/mounting*
Tightening torque adjustment
Selecting the drill position
Change rotation speed
How to use the LED light
Mounting the bit
Reversing the rotational direction
Switch operation
Remaining battery indicator
Mounting and removing the hook
(sold separately)
Selecting accessories
*1 The bit for Bit adapter and Off -set adapter
NOTE
The axis-position 13 mm bit and the double-ended bit
cannot be properly attached with the Bit adapter or the
Off -set adapter. Do not use them with the Bit adapter or
the Off -set adapter. There is a risk of them falling from
the tool during work.
When using these, use the Chuck adapter.
*2 Adapter removal/mounting
Removal: Push the interlock ring forward (a) and pull off
the chuck adapter (b).
Mounting: Push the interlock ring forward and move the
chuck as far as the limit stop on the drill spindle.
NOTE
○ When performing drilling work, mount the Chuck
adapter.
○ The Bit adapter and Off -set adapter are for screw-driving
work for wood screws, etc. Do not use them for drilling
work.
○ When using the Angle adapter, mount the Chuck adapter
or the Bit adapter.
Figure Page
1
3
4
5
2
6
7
8
9
10
11
12
13
14
― 172
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 3. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
Safeguard
Function
Overburden
Protection
Temperature
Protection

MAINTENANCE AND INSPECTION

1. Inspecting the tool
Since use of as dull tool will degrade effi ciency and
2
cause possible motor malfunction, sharpen or replace
2
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
2
Regularly inspect all mounting screws and ensure that
3
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
3
result in serious hazard.
3
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
3
tool. Exercise due care to ensure the winding does not
3
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
4
Check to make sure that swarf and dust have not
4
collected on the terminals.
On occasion check prior, during and after operation.
4
CAUTION
4
Remove any swarf or dust which may have collected on
the terminals.
4
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
6. Storage
Store the power tool and battery in a place in which
the temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
10
Table 3
LED Light
Corrective Action
Display
If the operating with the
shift knob set on HIGH,
On 0.1 second/
adjust to LOW and
off 0.5 second
continue operation.
Remove the cause of
the overburdening.
On 0.3 second/
Allow the tool and
off 0.3 second
battery to thoroughly
cool.