EINHELL TP-RO 18 Li BL Manual De Instrucciones página 22

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 108
tive gloves at all times when handling cutting
tools.
To make it easier to change the cutter, re-
move the cordless routing unit (1) from the
respective insert as described in section 5.5
Cutters with a shaft diameter of 6 mm and 8
mm can be used in the cordless router. Most
cutters are available in both sizes.
You can use cutters made of the following
materials:
- HSS - suitable for cutting softwood
- TCT - suitable for cutting hardwood, particle
board and plastic
Select the appropriate cutting tool for the job
in hand.
When using the cutters for the first time:
Remove the plastic packaging from the cutter
heads.
Clean the nut, clamp and shaft of the cutter
before fitting it.
Undo the clamp nut (6) using the two open-
ended wrenches (23).
If a cutter is already fitted in the clamp
(24/25), remove it.
Select the appropriate cutting tool (f) for the
job in hand.
Select the appropriate clamp (24/25) for the
cutter you want to use.
Now insert the clamp (24/25) in the cutting
spindle (Fig. 8).
Refit the clamp nut (6) (Fig. 9).
Guide the cutter shaft into the clamp (Fig. 10).
While holding the spindle lock (5) in pressed
position, screw the clamp nut (6) hand-tight
(Fig. 10).
Notice!
The spindle lock is not allowed to be used for
tightening with the open-ended wrench (23)!
Tighten the clamp nut (6) using the two open-
ended wrenches (23).
The cutter must be inserted into the clamp
(24/25) by at least 20mm.
Before you use the equipment, check that the
cutting tool is secure and runs true.
5.7 Adjusting the end stops (Fig. 12/Item 13)
The end stops (13) can be adjusted in height
according to requirements. To do so, use a hex
key to turn the screw on the end stop (13) to the
required stop height.
Warning! Remove the setting and assembly
tools again before starting the machine.
Anl_TP-RO_18_Li_BL-Solo_SPK13.indb 22
GB
6. Operation
Never use a low-quality or damaged cutter.
Use only cutting tools with a shaft diameter of
6 mm or 8 mm. The cutters must also be desi-
gned for the respective idling speed.
Secure the workpiece so that it cannot be
thrown through the air as you work on it. Use
clamps or a vise.
Never cut over metal parts, screws, nails etc.
6.1 On/Off switch (Fig. 1/Item 3)
For safety reasons, the cordless router is
equipped with a safety lock-off .
To switch on, press the unlock/lock button (2).
The LED lamp (29) will begin to shine by way
of confirmation.
Now press the On/Off switch (3) within the
next 10 seconds.
If the On/Off switch is not pressed for longer
than 10 seconds, the LED lamp (29) will go
out and the equipment cannot be switched
on.
To switch off, press either the unlock/lock but-
ton (2) or the On/Off switch (3).
6.2 Speed control (Fig. 12/Item 4)
The most suitable speed depends on the material
you want to cut and on the diameter of the cut-
ter. Use the speed control switch (4) to select a
speed between 10,000 and 30,000 min
choose from 6 diff erent switch positions.
The speeds in the various switch positions
are as follows:
Switch position 1: approx. 10,000 min
speed)
Switch position 2: approx. 14,000 min
Switch position 3: approx. 19,000 min
Switch position 4: approx. 22,000 min
Switch position 5: approx. 25,000 min
Switch position 6: approx. 30,000 min
speed)
To increase the speed:
Move the speed controller (4) in the plus direction.
To decrease the speed:
Move the speed controller (4) in the minus direc-
tion.
- 22 -
. You can
-1
(minimum
-1
-1
-1
-1
-1
(maximum
-1
11.07.2022 08:42:30

Publicidad

Tabla de contenido
loading

Tabla de contenido