Safco 3470 Instrucciones De Montaje

an LDI Company
New Hope, MN 55428
Visit us on the web:
www.safcoproducts.com
PRODUCT WARRANTY REGISTRATION is available online at: www.safcoproducts.com
READ THESE INSTRUCTIONS BEFORE STARTING
FOLLOW THE ASSEMBLY PROCEDURES CAREFULLY
LETTER
DESCRIPTION
CODE
Base
A
Casters
B
Pump Assembly
C
Pump Dust Cover (3-piece)
D
Seat Assembly: 3470
E
Small Screw (Silver)
F
(temporarily installed on sides of
seat cushion and back rest)
Back Rest:
G
Screw Cover
H
Right Arm (marked "R")
I
Left Arm (marked "L")
J
1
Turn the A Base upside down and insert the five B
Casters into the ends of the Base spokes. Turn the Base
right side up.
2
Insert the C Pump Assembly into the base, tapered end
down. Secure the Pump Assembly by applying a little
downward pressure. DO NOT PUSH ON BUTTON AT
THE TOP!
3
Slide the D Dust Cover over the Pump Assembly until
it meets the Base.
4
Remove the F Small Screws (Silver) from the sides of the
Seat Cushion and from the sides of the G Back Rest.
ATTENTION:
fasten the screws; do NOT fully tighten the screws until all
screws are properly inserted. THEN, go back and tighten
each screw evenly.
1. Adjust height of chair:
•
Keep feet flat on the floor.
•
With lever on right side,
adjust height so you feel NO
pressure under the back of
your thighs.
3470-37: 1 of 2; Rev. 4; 9/05
All manuals and user guides at all-guides.com
Serenity Leather Office Chair
A S S E M B L A S A S S E M B L S E M B L Y Y Y Y Y S E M B L
A S A S S E M B L
TOOLS REQUIRED: Screwdriver
PARTS LIST
QTY. PART NO.
1
5
1
1
1
or 3471 1
or 3472 1
8
3470 1
or 3471 1
or 3472 1
8
1
1
For steps 5 and 6, temporarily
For questions or concerns, please call the
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
Safco Products Company, New Hope, MN 55428
I N S T R U C T I O N S I N S T R U C T I O N S I N S T R U C T I O N S
I N S T R U C T I O N S I N S T R U C T I O N S
G
3470-02
3470-25
I
3470-11
3470-14
3470-51
3471-51
3470-51
3470-23
F
H
3470-04
3471-04
3472-04
3470-22
3470-08
3470-09
5
Mount the J Left Arm to the left side of the G Back
Rest, using two Small Screws (Silver). Now do the
same with the I Right Arm on the right side of the G
Back Rest.
6
Place the E Seat Assembly between the Arms and line
up the holes in its sides with those in the Arms. Secure
with the Small Screws.
7
Go back and tighten each screw evenly using a screw-
driver and cover the screws with the H Screw Covers.
8
Place the E Seat Assembly onto the Pump Assembly.
Press down firmly (or sit) to lock into place.
9
Adjust the chair height and chair tension as needed,
following the instructions shown below.
D
A
2. Adjust the chair tension:
•
Loosen the knob under the front
of the chair to allow easier tilting.
•
Tighten the knob to provide a
firmer action.
3470
MODEL
3471
NUMBERS
3472
J
E
C
B