Environmental Protection; Technical Specifications - Metabo MA-FS 40 Manual Original

11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Cordless multifunction drive MA 36-18 LTX
BL Q, order no.: 601725850
B Thicket blade, 3-wings, Ø 255 mm, incl.
protective cover (as spare):
Order no.: 628432000
C Grass blade, 4-wings, Ø 254 mm, incl.
protective cover:
Order no.: 628433000
D Replacement line Ø 2 mm, wave-shaped:
Order no.: 628430000
E Replacement line Ø 2 mm, spiral-shaped:
Order no.: 628423000
F Complete line head (complete housing incl. reel
and cutting line, (as spare)
Order no.: 628429000
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians and only with
original spare parts!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).

14. Technical Specifications

Explanatory notes regarding the specifications on
page 4.
Subject to change in accordance with technical
progress.
Measured values determined with cordless
multifunction drive MA 36-18 LTX BL.
B = cutting width
H = max. cutting line length
H = cutting line diameter
X
n = no-load speed
0
m = weight (without cordless multifunction
drive, battery pack, carry strap)
Measured values determined in conformity with
EN 50636-2-91+EN ISO 22868.
Permitted ambient temperature during operation:
-20 °C to 50 °C (limited performance with
temperatures below 0 °C). Permitted ambient
temperature for storage: 0 °C to 30 °C
Recommended ambient temperature when
charging: 0 °C to 40 °C
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three
directions):
a = vibration emission value
h
K = uncertainty (vibration)
h
Typical A-weighted sound levels:
L = sound pressure level
pA
L = sound power level
WA
K , K = uncertainty
pA WA
L = measured sound power level as per 2000/
WA(M)
14/EC
L = guaranteed sound power level as per
WA(G)
2000/14/EC
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
ENGLISH en
19