Using The Transmitter - King gates DIGYPAD Instrucciones De Instalación

WARNINGS
• The transmitter can be installed externally or internally;
• it must be installed on a vertical wall, consisting of solid
material providing stable anchorage;
• it must be positioned at a height of 1.5 m from the ground, to
facilitate entering passwords and commands.
• The transmitter range and the receiver reception capacity can
be disturbed by various factors:
a) the devices are too far apart (see limits in Chapter 7);
b) the presence of other devices operating on the same
frequency (for example: alarms, earphones, etc.) in the
immediate vicinity;
c) metal surfaces on which the transmitter is placed (they can
shield transmission);
d) flat battery (which can reduce the radio range by 20-30%).
In all such cases, the manufacturer cannot provide any
guarantee regarding the actual range of its devices.
2. Place the transmitter provisionally in its desired location for
installation, but do not fix it permanently.
3. Perform commands on all the automations concerned,
checking to see that they receive the commands. If the reception
is poor, read the warnings in step 01. Try to move the transmitter
to a more favourable position and repeat the tests for sending
commands to the automations.
3.3 - Installing the transmitter in the
intended position
After you have checked the operation of the transmitter, install it
definitively as shown in fig. 2, 3, 4, 5, 6 and 7.

4 - USING THE TRANSMITTER

To command an automation (or a group of automations) you
must first enter the security password and, immediately after,
the command key (A, B or C) paired with the password you
have just entered.
Note – As you enter the password and the command, after
pressing one key you have 6 seconds to press any other key. If
this time elapses, the password must be entered again, starting
from the beginning.
The product leaves the factory with three preset security
passwords, each paired with a command key (A, B, C).
The passwords are:
• password 1 - 1 (paired with key "A");
• password 2 - 2 (paired with key "B");
• password 3 - 3 (paired with key "C").
CAUTION! – Since all DIGYPAD transmitters have the same
default passwords, we recommend that you replace the
factory preset security passwords with personal and
confidential ones, in order to exploit the confidentiality potential of
the product (see paragraph 4.1).
Security passwords can also be disabled (see paragraph 4.1.1) or
re-enabled (paragraph 4.1.2).
The password must be entered correctly in order to be able
to send commands. If you make a mistake while entering the
password, you should immediately press the command key (A,
B or C) paired with the password and wait for the error signal (5
beeps!). When it stops, enter the password again.
10
4.1 - How to change one of the three current
security passwords
CAUTION! – The following procedure shows you how to change
the password associated with command key "A".
To change the password associated with command key "B", redo
the procedure from the beginning by pressing key "B" in steps
01, 03, 05 and 07. Use the same logic to change the password
associated with command key "C".
1. Press and hold down "0"; then press and release the
command key paired with the current password that you
wish to change (in this example it is key "A"); lastly, release
the button "0".
2. Enter the current password paired with the command key
pressed in step 01 (if the current password is still the factory
default one, enter the password shown in the Chapter 4).
3. Press and release the command key "A".
4. Enter the new password
5. Press and release the command key "A".
6. Enter again the new password you just created in step 04.
7. Press and release the command key "A": the transmitter
emits 3 beeps to indicate that the setting has been changed
successfully. If it beeps 5 times, then the new setting has not
been saved.
(1) Note – The new password may be composed of up to eight
digits, as the user prefers. Each digit can take a numerical value
as required, from "0" to "9".
4.2 - How to disable confidential use of the
transmitter
Carry out the procedure detailed in paragraph 4.1, omitting
steps 04 and 06.
This programming eliminates the requirement to enter the security
password each time you want to send a command to the
automation.
CAUTION! – This setting deletes the confidentiality of the
transmitter, making it usable without a password and, therefore,
also by unauthorized persons.
ATTENZIONE! – L'impostazione elimina la riservatezza del
trasmettitore, rendendolo usabile senza password e, dunque,
anche da persone non autorizzate.
4.3 - How to re-enable confidential use of
the transmitter
Carry out the procedure detailed in paragraph 4.1, omitting
step 02. This programming restores the requirement to enter the
security password each time you want to send a command to
the automation. This setting re-enables the confidentiality of the
transmitter, making it usable only by those in possession of the
password and, therefore, only by authorized persons.
you want.
(1)