Safety Warnings - Surtek 30.3120.90 Manual De Usuario Y Garantía

SAFETY WARNINGS

FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and
paint fumes, in work area can ignite or
explode. To help prevent fire and explo-
sion:
• Use equipment only in well ventilated
area.
• Eliminate all ignition sources; such as
pilot lights, cigarettes, portable electric
lamps, and plastic drop cloths (potential
static arc).
• Keep work area free of debris, including sol-
vent, rags and gasoline.
• Do not plug or unplug power cords or turn
lights on or off when flammable fumes are pres-
ent.
• Ground equipment and conductive objects in
work area.
• If there is static sparking or you feel a shock,
stop operation immediately. Do not use equip-
ment until you identify and correct the problem.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not exceed the maximum working pressure
or temperature rating of the lowest rated sys-
tem component.
• Use fluids and solvents that are compatible
with equipment wetted parts. Read fluid and
solvent manufacturer's warnings.
• Check equipment daily. Repair or replace worn
or damaged parts immediately.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose.
• Route hoses and cables away from traffic ar-
eas, sharp edges, moving parts, and hot surfaces.
• Do not use hoses to pull equipment.
• Keep children and animals away from work
area.
• Comply with all applicable safety regulations.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or
death if splashed in the eyes or on skin, inhaled,
or swallowed.
• Read MSDS's to know the specific hazards of
the fluids you are using.
• Store hazardous fluid in approved containers,
and dispose of it according to applicable guide-
lines.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equip-
ment when operating, servicing, or when in the
operating area of the equipment to help protect
you from serious injury, including eye injury, in-
halation of toxic fumes, burns, and hearing loss.
E N G L I S H •
This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by
the fluid and solvent manufacturer
• Gloves
• Hearing protection
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks,
or ruptured components can splash in the
eyes or on skin and cause serious injury.
• Follow Pressure Relief Procedure in this manu-
al, when you stop spraying and before cleaning,
checking, or servicing equipment.
• Tighten all fluid connections before operating
the equipment.
• Check hoses, tubes, and couplings daily. Re-
place worn or damaged parts immediately.
OPERATION INSTRUCTIONS
SETUP
1. Install an air pressure regulator on gun air
supply line to control air pressure.
2. Install a shutoff valve downstream of the air
regulator to shut off gun air.
3. Connect a clean, dry, filtered air supply.
4. Connect air supply line to gun air inlet. Con-
nect other end to shutoff valve.
FLUSH SPRAY GUN
Flush spray gun before using it. Use solvent that
is compatible with gun wetted parts and fluid
that will be sprayed. Use lowest possible pres-
sure, and spray into grounded metal waste
container. After flushing, follow Pressure Relief
Procedure.
PRESSURE RELIEF PROCEDURE
1. Turn off gun air supply.
2. Trigger gun into grounded metal waste con-
tainer.
WARNING: Follow pressure relief procedure
when you stop spraying and before cleaning,
checking, or servicing equipment.
ADJUST SPRAY PATTERN
1. Rotate air cap to change
spray pattern direction.
2. For maximum fluid flow and
to prevent premature fluid
nozzle wear, turn fluid adjustment knob left un-
til no trigger restriction is felt; trigger should be
able to touch gun handle. Then turn knob out
1/2 turn more.
3. If further fluid flow restriction is needed, use
different size needle/nozzle/air cap combina-
tion. If necessary, fluid adjustment knob can be
U ser's manual
5