Jung IPS200REG-01 Instrucciones De Servicio

IP interface
Safety instructions
CAUTION
Read all instructions first before
mounting the product.
Do not drink any alcohol or take any
drugs before or during the mounting
of the product. Follow the safety inst-
ructions carefully.
This device is intended for installa-
tion in accordance with the National
Electric Code® and local regulations
in the United States. If you are unsure
or uncomfortable about performing
this installation consult a qualified
electrician.
These instructions are an integral part
of the product, and must remain with
the end customer.
This device is only intended to be
used in cooperation with the KNX-
Bus.
Function
System information
This device is a product of the KNX system and
conforms to the KNX Directives. Detailed knowled-
ge attained through KNX training is a prerequisite
for understanding.
The device function is software-dependent. De-
tailed information about software versions and the
respective function scope, as well as the software
itself can be found in the manufacturer's product
database. The device is planned, installed and com-
missioned by means of KNX-certified software. The
product database and the technical descriptions can
be found on our website at all times.
Correct use
• Operation as data interface
• Installation on top-hat rail in sub-distributor
i Depending on usage, requirements for access,
data security and data volume, it may make
sense for individual services that use the IP
network to install their own network paths.
Product characteristics
• L ED display for KNX communication, Ethernet
communication and programming mode
• C onfiguration via ETS
• Max. 4 connections to IP terminal devices, e.g.
for simultaneous visualisation and configuration
• Supply from network line – Power-over-Ethernet
to IEEE 802.3af –, through separate voltage
supply or the auxiliary voltage output of the
KNX voltage supply.
• Electrical isolation between KNX and IP net-
work.
Information for electrically skilled
persons
Installation and electrical connection
WARNING
Class 2 power wiring only.
The device must be mounted and
commissioned by an authorized
electrician.
The prevailing safety rules must be
heeded.
The device must not be opened. A
device suspected faulty should be re-
turned to the local JUNG sales office
or distributor.
Installation and electrical connection (Figure 1)
(6)
(7)
(8)
PROG PROG BUS BUS LAN (PoE) LAN (PoE)
Bereich:
Bereich:
Linie:
Linie:
TLN- TLN-
IP-Schnittstelle Nr.:
Nr.:
IPS 200 REG
AC 16 ... 24 V Made in Germany
AC 16 ... 24 V
DC 20 ... 30 V
DC 20 ... 30 V Made in Germany BUS - + BUS - +
fig.1
(1) LAN (PoE)
(2) Programming key
(3) Field for phys. address
(4) KNX connecting terminal
(5) Voltage supply AC/DC 20..30 V
(6) Green LED: LAN activity
(7) Yellow LED: KNX bus activity
(8) Red LED: programming mode
CAUTION
System components have to be sup-
plied by either: Source that complies
with Limited Power Source acc. UL
60950-1 (LPS)
or
NEC Class 2 circuit Rated
16 - 24 V AC or 20 - 30 V DC,
min. 150 mA
or
IEEE 802.3af (PoE)
Start-up
Network default setting is DHCP.
The boot time is approx. 2 seconds.
The green LED flashes to indicate activity on the
LAN connection, the yellow LED indicates KNX
bus activity. The red LED is active when the KNX
address programming key at the interface has been
pressed.
Parameterization
The device is parameterised via ETS3 or ETS4.
The KNXnet/IP interface (3TE) supports up to four
KNXnet/IP-tunnel connections.
Technical data
KNX medium TP
Commissioning mode S-mode
Power supply External 16-24 V AC or
20-30 V DC; IEEE 802.3af
(„Power over Ethernet")
Power draw Maximum 1 W
KNX functions KNXnet/IP tunnelling
KNXnet/IP tunnelling Up to 35 telegrams per
second, up to four inde-
pendent tunnel connec-
tions
Warranty
If you have any questions about this product,
contact:
Jung USA, Inc.
350 Fifth Avenue, Suite 5220
New York, NY 10118
Phone: +1 800.311.6135
Email: sales@jungcontrols.com
www.jungcontrols.com
For the product warranty, please refer to the atta-
ched document.
All rights reserved
(1)
(2)
IP interface
(3)
Art.-Nr.: IPS200REG-01
USA E
(4)
(5)
© ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-2 04
kundencenter@jung.de
www.jung.de
0024019200 05.07.2017