General Safety - MaxPro PROFESSIONAL MPPW800 Manual De Instrucciones

safety warnings and all instruc Failure to follow the warnings and instruc
shock, fire and/or serious injury. Make sure the voltage corresponds to the type label on the unit. Packing
materials are no toys! Children must not play with plas
output may exceed 85dB(A) at the workplace. In this instance, wear ear prot

GENERAL SAFETY

Read all safety warnings and all ins
electric shock, fire and/or serious injury.
Save all warnings and ins for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or ba ery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Clu ered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while opera
control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet c
of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of
electric shock.
e) When opera a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f) If opera a power tool in a damp loca
protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when opera
a power tool while you are red or under the influence of drugs, alcohol or medica
ina en ra ower tools may result in serious personal injury.
b) Use personal prot ve equipment. Always wear eye prot
mask, non-skid safety shoes, hard hat, or hearing prot
personal injuries.
c) Prevent uninten st g. Ensure the switch is in the off-
source and/or ba ery pack, picking up or carrying the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on invites accidents.
d) Remove any adjus key or wrench before turning the power tool on. A wrench or a key le a ached
to a rota part of the power tool may result in personal injury. e) Do not overreach. Keep proper f
and balance a This enables be er control of the power tool in unexpected situa
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from
moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the c
connected and properly used. Use of dust c
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your applica
will do the job be er and safer at the rate for which it was designed.
2
may result in electric
ger of suffoca The power tool noise
Failure to follow the warnings and ins
a power tool. Distr can cause you to lose
Water entering a power tool will increase the risk
is unavoidable, use a residual current device (RCD)
a power tool. Do not use
. A moment of
Protec ve equipment such as dust
used for appropriate c
before c
of dust extr and c f ensure these are
can reduce dust-related hazards.
The correct power tool
GB
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the ba ery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preven ve safety measures
reduce the risk of st
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power
tool or these ins
users.
may result in
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other c
before use. Many accidents are caused by poorly maintained power tools.
f) Keep cu
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instruc ons, taking into
account the working c
Use of the power tool for opera
5) Service
a) Have your power tool serviced by a qualified repair person using only iden cal replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTION FOR PIPE WELDING TOOL
The product uses a single-phase tripolar plug which cannot be changed by the user without approval. For
applica
During opera
electrical fusion splicer to avoid accidents which may result in personal injury.
Any non-professional is not permi ed to start the fusion splicer to prevent electrical shock and damages to
the security structure and performances of the tool.
If the red indicator is always on/off, it may indicate that the instrument fails. Thereby, Shut off it
immediately and cut off the power. The instrument cannot be used un
The instrument with faults (if any) shall be sent to the local distributor or manufacturer for maintenance.
Any user is not permi ed to dismantle the instrument without approval.
Before delivery, the maximum hea
Therefore, any nonprofessional shall not regulate it randomly to avoid the adverse effect on its normal
opera
SYMBOLS
s will reduce
g to power
ower tool accidentally.
to operate the power tool. Power tools are dangerous in the hands of untrained
that may affect the power tool's opera
tools sharp and clean. Properly maintained cu
work to be performed.
fferent from those intended could result in a hazardous situa
gged in a socket with earth wire.
hands and flammable and explosive objects shall not contact the thermo-block of the
temperature of the fusion splicer is regulated in the factory.
rvice life.
Read the manual
Warning
GB
If damaged, have the power tool repaired
tools with sharp cu edges are less
roubles are eliminated.
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
3