Manuales relacionados para Truper SOPLA-26
Resumen de contenidos para Truper SOPLA-26
- Página 1 Manual Gas Backpack Blower SOPLA-26 Applies for: Code Model 18147 SOPLA-26 26 cc Motor Read this Manual thoroughly CAUTION before using the tool.
- Página 2 Contents CAUTION Technical data Fuel Specifications To gain the best performance of the tool, prolong the duty life, General motor tool safety warnings make the Warranty valid if necessary, and to avoid hazards Safety Warnings for the Use of Blowers of fatal injuries please read and understand this Manual before Parts...
- Página 3 Technical Data SOPLA-26 Code 18147 Description Gas Backpack Blower Net Weight 12.5 lb Motor 26 cc Air Speed 180 MPH Air volume 335 CFM Sound Level 109 dB Motor Rated Power 0.85 HP Motor Maximum Speed 8500 RPM Idle Speed 2 800 RPM –...
- Página 4 General Motor Tool safety Warnings Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury.
- Página 5 Safety Warnings for Using Blower • Safety is a combination of common sense, alert mind and knowledge about how the tool works. CAUTION • Read the manual carefully before you start using the tool. Pay close attention to safety rules, alert symbols and danger, warning and attention labels.
- Página 6 Parts Choke Lever Fuel Primer Tank Cap Bulb Shoulder Harness Elbow Hose Spark Plug Base Jack-Line Fuel Tank Switch Choke Lever Handle Throttle Carburator Idle Blocking Button cover Front screw extension Primer Bulb Throttle Trigger Jack-Line Rear extension Shoulder Harness Wide Narrow Blower Nozzle...
- Página 7 Fuel Supply Fuel Supply for the Motor • Follow the Safety Standards for fuel handling (page 5). • Clean the surface around the fuel tank cap to prevent contamination. • Slowly loosen the fuel tank cap. • To avoid any spills carefully pour the fuel mix into de tank.
- Página 8 Start Up Starting a Warm Motor • Set the blower on its base on leveled ground. • Set the switch in the ON position (A). • Press and release the primer bulb 10 times (B). • Press the throttle trigger and block with the blocking ≤...
- Página 9 Maintenance • Before inspecting, cleaning or servicing the tool, turn off the motor. Wait until all moving parts stop. Disconnect the spark plug cable and separate it from the spark plug. Otherwise you could get severely injured and/or the tool gets damaged. Cleaning the Air Filter Spark Plug Replacement •...
- Página 10 Maintenance Regular Maintenance Table Visual inspection (general condition, wear leaks) Complete machine Clean Handle Check functioning Clean Air filter Replace* Check Fuel tank filter Replace filter* Fuel tank Clean Stable speed while empty Carburetor Carburize* Adjust gap between electrodes* Spark plug Replace Substitute* Exhaust...
- Página 11 Troubleshooting Problem Cause Solution The motor will not • There is no spark. • Verify the spark. Remove the motor cover. Remove the spark plug from start. the cylinder. Connect the spark plug cable and set it onto the motor cylinder with the metal side touching it.
- Página 12 Notes ENGLISH...
- Página 13 In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center.
- Página 14 It includes the costs of transportation of the product that derive from its fulfillment of its service network. . Phone number 800-018-7873. Made in China. Imported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.