Led Status Indicators; Maintenance, Care, Storage And Transportation; Disposal Instructions - Goobay 58481 Manual De Instrucciones

Splitter HDMI™ da 1 a 2 (4K @ 60 Hz)
EN
3 Intended use
This product is intended exclusively for private
use and its intended purpose. This product is
not intended for commercial use. We do not
permit using the device in other ways like described in
chapter „Description and Function" or in the „Safety Ins-
tructions". Use the product only in dry interior rooms.
Not attending to these regulations and safety instructi-
ons might cause fatal accidents, injuries, and damages
to persons and property.
4 Preparation
1. Check the scope of delivery for completeness and
integrity.
2. Compare the specifications of all used devices and
ensure compatibility.
5 Connection and operation
5.1 Connection
NOTICE!
• Disconnect the power supply to the splitter before
connecting or disconnecting your source and output
devices via the HDMI™ sockets.
See Fig. 2.
1. Connect one source device to the HDMI™ socket
(input) (2) of the splitter.
2. Connect two output devices to the HDMI™ sockets
(output) (3) of the splitter.
Connection cables are not included in the delivery.
Make sure that the source and output devices as well
as the connection cables support the resolutions and
standards of the product!
3. Connect the USB-A plug (8) of the charging cable to
the USB-A socket (7) of the power supply.
4. Plug the Euro plug (6) of the power supply into a
free and easily accessible socket.
5. Connect the micro USB plug (9) of the charging ca-
ble to the micro USB socket (1) of the splitter.
The splitter is now supplied with power.
6. Disconnect all cable connections after use.
5.2 EDID function
The splitter has an additional EDID function (EDID =
Extended Display Identification Data). This function is
used to correct possible display errors. If you are satis-
fied with the display on both output devices, you do not
need to make any further adjustments. To use this func-
tion, the connected units must support the Auto EDID
function.
By pressing the EDID key (4) you can choose between
2 modes:
• Copy EDID (A): In this setting, the same resolution
is displayed on both output devices. The output de-
vice connected to the HDMI™ socket (output, OUT
1) determines the resolution.
If the output device on OUT 1 supports a higher re-
solution (e.g. 4K) than the output device on OUT 2
(e.g. 1080p), then the function is not supported and
the output devices will display a different resolution.
Under certain circumstances, no picture is displayed
on output device OUT 2.
• Mixed EDID (B): In this setting, a different resolution
is displayed on the output devices.
The desired resolution can be selected in the set-
tings of the output devices.
REV2022-11-11 Subject to change without notice.
V1.0aw
Material damage

5.3 LED status indicators

Name Description
When the LED is lit, power is sup-
POWER
plied to the splitter.
When the LED is lit, Mixed EDID (B)
B
mode is selected.
When the LED is lit, Copy EDID (A)
A
mode is selected.
When the LED is lit, the output de-
vice connected to the HDMI™ so-
2
cket (output, OUT 2) is properly con-
nected and switched on.
When the LED is lit, the output de-
vice connected to the HDMI™ so-
1
cket (output, OUT 1) is properly con-
nected and switched on.
When the LED is lit, the source de-
vice connected to the HDMI™ so-
IN
cket (input) is properly connected
and switched on.
6 Maintenance, Care, Storage and
Transportation
The product is maintenance-free.
NOTICE!
• Always disconnect the mains plug before cleaning.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a
dry and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.

7 Disposal instructions

According to the European WEEE directive,
electrical and electronic equipment must not be
disposed with consumers waste. Its compo-
nents must be recycled or disposed apart from
each other. Otherwise contaminative and hazardous
substances can damage the health and pollute the en-
vironment.
As a consumer, you are committed by law to dispose
electrical and electronic devices to the producer, the
dealer, or public collecting points at the end of the devi-
ces lifetime for free. Particulars are regulated in natio-
nal right. The symbol on the product, in the user manu-
al, or at the packaging alludes to these terms. With this
kind of waste separation, application, and waste dispo-
sal of used devices you achieve an important share to
environmental protection.
WEEE No: 82898622
- 5 -
Pillmannstraße 12 | 38112 Braunschweig | Germany
58481
Material damage
Goobay® by Wentronic GmbH