Publicidad
6. Different ways of cleaning
•
General Cleaning — use only tap water. Use warm temperature about 50ºC.
•
Enhanced Cleaning — add few drops of standard washing up liquid, liquid soap, or
into water, other non-acidic cleaning agents can also be used.
•
Extensive Cleaning — removing tarnish, carbon & rust from non-plated metals, it is recommended
to use specialist cleaning solution in associated using ultrasonic cleaner.
WARNING: Strong acid or alkaline cleaning solution will cause corrosion, rust and even
puncture of tank or machine body. To overcome this problem, dilute to mild PH solution or
request for tank made of specific grade of stainless steel like SUS304.
The cleaning solution will deteriorate in effectiveness over time and use. It is important to regularly
change the fluid and carefully wash the inside of the cleaning tank in order to preserve the effectiveness
and longevity of the cleaner. Do not use corrosive or abrasive cleaning products on the tank, which
must be wiped down and dried before it can be re-connected to the electrical supply.
NOTE: If the machine starts to spark, smoke, smell of burnt electrics or displays any other
fault the operator must immediately stop the machine, isolate the electrical supply and con-
tact the supplier. Continued use is dangerous.
6.1. Advantage
Ultrasonic is widely used throughout industries to remove difficult contaminants from the parts during
or after manufacturing process which might require a stage of cleaing before the next process. In
general, if an item can be cleaned with liquid, it can be cleaned much faster and more thoroughly with
an ultrasonic cleaner, Compared to traditional solvent/scrubbing methods of cleaning in a parts washer,
our ultrasonic cleaners:
•
Are more effective at removing contamination
•
Are quicker to achieve the results you want
•
Save employee time (and consequently money) by enabling 'switch on and leave' cleaning
•
Are heated to allow cleaning solvents to work more effectively
•
Use mechanical timers for simplicity, precision and longevity
•
Produce less mess during use
•
Less chemistry
•
Reproducible result
User's manual from ZCC016 to ZCC022
ENGLISH
detergent
Page. 16
Version 1, October 2022
3. Safety precautions
Keep it away from children!
This device is not intended to use by individuals with restricted physical sensory or metal capacities
or those with lack of experience or knowledge, include children, unless they are supervised by an
individual who is responsible for their safety or have received training in operating the device.
Please read the following very carefully as failure to comply may invalidate your gua-
rantee
1.
DO NOT run the cleaner continuously for more than one hour at a time, as doing so can damage
the internal components.
2.
DO NOT operate the unit without fluid in the tank. Always ensure the fluid is no higher than the
max mark. Always ensure there is a minimum depth of 7cm. Ideally 2/3 of the tank capacity
should be filled.
3.
Strong acids or flammable cleaners are strictly prohibited. If solvent type cleaner is added in the
tank, please stop working for a while after the 30-minute cycle.
4.
DO NOT drop any item into the tank as this may cause damage to the transducer. Always place
the items gently into the tank and use the basket whenever possible.
5.
The more items that you place in your cleaning bath the less efficient it will clean.
6.
It is not advised to overlap items. Always allow plenty of clear space between the items.
7.
Do keep cap on during use. This will prevent splashing and reduce liquid evaporation as well as
reduce equipment noise.
8.
Never immerse the machine or power cord in water or other liquid.
9.
DO NOT touch the power plug with wet hands, especially when inserting or removing the plug.
10. DO NOT touch the unit if the machine has fallen into water during operation. Remove the power
plug from the socket first.
11. DO NOT disassemble the machine, except by professionals.
12. UNPLUG the power source while filling or emptying the tank.
13. DO NOT spray water or liquid over the device and the control panel
14. DO NOT operate the cleaner without proper grounding.
15. DO NOT place the device on a soft surface, where the vents could be blocked.
16. Always turn the heater off after using as leaving it on can cause the fluid to evaporate and damage
the internal components.
17. Upon completion of the cleaning cycle, turn the heater button off and isolate the machine from
the electrical supply.
18. Take care when adding or removing items from the cleaning tank as the fluid is likely to be hot
and displaced fluid can damage the internal components. Any displaced fluid must be dried up
immediately.
19. In the event of failure/emergency, disconnect the mains supply by removing the plug from the
mains socket.
User's manual from ZCC016 to ZCC022
ENGLISH
Page. 13
Version 1, October 2022
Publicidad
