Publicidad
Idiomas disponibles
Idiomas disponibles
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
If using a multi-functional product it is not necessary to
add rinse aid; however,
Follow the instructions given on the
packaging.
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID* indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the
lid (G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure
it does not overflow from the
dispenser. If this happens, clean the
spill immediately with a dry cloth.
F
3. Screw the lid back on.
G
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Open the door and switch on the machine by pressing the
ON/OFF button.
- Press the P button and hold for approximately 5 seconds;
two short beeps will sound and the indicator light
corresponding to the set degree of hardness will flash
slowly on the display (the water softening system is set to
All manuals and user guides at all-guides.com
number 3).
- Press the P button repeatedly until the desired hardness
level has been reached (1-2-3-4-5* see Water hardness
table ).
E.g. hardness 1 (indicator light 1 illuminated)
hardness 2 (indicator light 1 illuminated, indicator light 2
flashing).
hardness 3 (indicator lights 1 and 2 illuminated, indicator light
3 flashing and so on).
- To exit the function, wait approximately 30 seconds or switch off
the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
°dH
°fH
0
11
0
20 1.1
12
17
21
30 2.1
17
34
31
60 3.1
34
50
61
90 6.1
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined
salt removes limescale from the water, thus avoiding the
formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher ( see Description ) and should be filled:
• When the green float* cannot be seen by simply looking at
the cap of the salt dispenser.
• When the LOW SALT* indicator light on the control panel is
illuminated;
1. Remove the lower rack and
unscrew the cap of the dispenser
(in an anti-clockwise direction).
2. For the first wash cycle only: fill
the dispenser up to the edges with
water.
3. Position the funnel* correctly ( see
figure ) and fill the salt dispenser up
to the edges (approximately 1 kg);
it is normal for a little water to leak out.
4. Remove the funnel, wipe away any salt residue from the
opening and screw the cap on tightly, so that detergent
does not leak into the dispenser during the wash cycle (this
could damage the water softening system beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
* Only available in selected models.
mmol/l
level
2
1
3
2
6
3
9
*
4
Publicidad
