Luminance Brands Kathy Ireland Home PRO Serie Manual Del Propietário página 2

Section
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1 . Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
2 . Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 . Installing the Hanger Ball/Downrod Assembly . . . . . . . . 5-7
4 . Installing the Ceiling Cover on the Fan Motor Housing . 8-9
5 . How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . .10-11
6 . Hanging the Ceiling Fan (Standard) . . . . . . . . . . . . . . . 11
7 . Hanging the Ceiling Fan (Close-to-Ceiling) . . . . . . . . . . 12
8 . How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . .13-14
9 . Installing the Ceiling Cover . . . . . . . . . . . . . . . . . . . . . . . 15
10 . Installing the Fan Blades . . . . . . . . . . . . . . . . . . . . . . . 16
READ AND SAVE THESE INSTRUCTIONS
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner's manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code "ANSI/NFPA 70-2017" and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
All manuals and user guides at all-guides.com
Table of Contents
Page
Safety Instructions
2
Section
11 . Installing the Glass Shades and Light Bulbs . . . . . . . . 17
12 . Removal of the Light Fixture . . . . . . . . . . . . . . . . . . . . . 18
13 . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
14 . Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . 19
15 . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16 . Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21
17 . Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . 23
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as "Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less", and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
CAUTION
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE:
The CF711 fan is suitable for use with solid-state
speed controls.
NOTE:
All set screws must be checked and re-tightened
where necessary before installation.
WARNING
!
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use this product
by Luminance Brands Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury or
property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
Page
U.L. Model No.: 42-ANT & 52-ANT