Auto Mate 7704A Dealer Master Guia Del Usuario

Quick Reference User's Guide
7704A Dealer Master Remote Control
Internal Antenna: transmits information
LED: Active during communication
Arm: Arms alarm and locks vehicle
Disarm: Disarms alarm and unlocks vehicle
AUX: (No function other than programming)
Car Finder
The dealer master remote is used for controlling the installed system
while the vehicle is on the sales lot. The remote itself has several
programming features that are described in this guide.
Assigning an ID Number
Before the remote is programmed to the system in the vehicle, it is
recommended that a 4 digit ID number is assigned to the remote
AUX: Press first, then press
(the factory default number is "0000"). Please record this number
Optional Remote Start if connected
in the box provided at the end of this section for future reference.
The following procedure describes how to assign an ID Number
to the remote.
1. Press and hold the
LED comes on solid (after approximately 10 seconds).
Note: The LED flashes once per second while the buttons are
depressed.
2. Release the buttons – the LED turns off
3. Press each command button associated with a digit of the ID
number the corresponding number of times conveyed by that
digit. The LED confirms each press.
Example: To enter ID 2104:
• Press 2 times
AUX
AUX
• Press 1 time
• Do not press
AUX
AUX
AUX AUX
• Press 4 times
4. Once the number is entered, wait for 20 seconds for the re-
mote to exit the routine.
Note: The LED flashes four times confirming the routine is ex-
ited.
5. The remote control is now ready for programming to the sys-
tem.
Record your selected ID number here:
© 2012 Directed. All rights reserved.
for Car Finder
& buttons simultaneously until the
AUX
AUX
AUX
AUX
AUX
AUX
Remote Programming
Use the following procedure to program a new remote to the sys-
tem:
1. Open a door and turn the ignition on.
2. Press/release once and then press/hold the Valet button until
one horn/siren sound confirms selection.
3. Release the button (Learning exits in 30 seconds if no action
is performed)
4. Press/hold the
turns on solid (after approximately 10 seconds). The horn/
siren emits 1 sound to confirm learning. For additional Dealer
Master remote controls, enter the same ID number of the origi-
nal Dealer Master Remote that has already been programmed
to the system.
5. Turn the ignition off or wait 30 second to exit programming,
the horn/siren emits 2 sounds to confirm.
ID Number Review Routine
If an ID number was assigned to a remote control but is forgotten,
the following procedure can be used to recall the ID Number as-
signed.
1. Press/hold the
AUX
AUX
comes on solid (after approximately 10 seconds).
Note: The LED flashes once per second while the buttons are
depressed.
2. Release the buttons – the LED turns off.
3. Press/release once, each command button associated with
a digit of the ID number. The LED flashes in groups to confirm
each digit.
Example: To recall the assigned ID number: 2104
Press
AUX
Press
Press
AUX
AUX
Press
4. Once the number is recalled, wait for 20 seconds for the
remote to exit the routine.
Note: The LED flashes four times confirming the routine is ex-
ited.
RF range adjustment routine
The transmission output strength of the remote control can be ad-
justed to fit the range needs of a particular lot. The factory default
range is the long intermediate setting.
Note: Range is based on line of sight, unobstructed testing under
ideal conditions. Actual range can vary due to local conditions
including, but not limited to the environment, terrain, vehicle loca-
tion and orientation, interference and other possible impediments.
button on the remote until the transmit LED
AUX
AUX
AUX
AUX
& buttons simultaneously until the LED
: The LED flashes 2 times, indicating first digit is 2
AUX
: The LED flashes 1 time, indicating second digit is 1
: No LED flashes occur, indicating third digit is 0
AUX
AUX
AUX
: The LED flashes 4 times, indicating fourth digit is 4 AUX
1