Publicidad
Idiomas disponibles
Idiomas disponibles
now be used to set the timer value.
The Minute Minder Timer will begin
counting down once it has been set, it will
not stop if the appliance is switched off or if
the Key Lock function is activated.
Once it has reached zero, "00" will be
displayed on the Timer Display and the
buzzer will sound. Press any button to stop
the buzzer sound.
Heater Timer
Heater Timers can only be set when a
heater has been activated, i.e. a heater
level must be set between 1 and 9.
Pressing
once will activate the Minute
Minder Timer, pressing
the timer to an activated heater. This will
be indicated by the corresponding Cooking
Zone Indicator flashing. Pressing
third time, after setting the first heater timer,
will activate the timer for the next active
heater in a clockwise direction. This will
be indicated by its corresponding Cooking
Zone Indicator flashing. Pressing
will allow the timer to be set a value for the
active heater.
The timer for the heater that was set first
will be indicated by the illumination of its
corresponding Cooking Zone Indicator.
Pressing
again allows more timers to
be assigned to the other activated heaters.
The Timer Display will change, 10 seconds
after the last operation, to the timer that
will run out next. The number of timers that
are running is indicated by the number of
illuminated Cooking Zone Indicators.
The timer values for the Heater Timer and
the Minute Minder Timer can be displayed
by pressing
, a Cooking Zone Indicator
will flash for the timer it is assigned to. If no
Cooking Zone Indicator flashes, the Minute
Minder Timer value will be shown on the
Timer Display.
All Heater Timers can be removed by
switching the appliance into S-Mode using
, however this will have no effect on the
Minute Minder Timer which will continue
counting down.
To remove a timer in Operation Mode,
first select the timer using the Activate/
Deactivate Timer Button until the desired
timer is displayed on the Timer Display. It
can then be removed in 2 ways:
•
Decrease the value by pressing
"00" appears on the Timer Display
•
Press
and
seconds until "00" is shown on the Timer
again will assign
for a
and
until
simultaneously for 0.5
Display.
Once a timer reaches "00", the level of its
corresponding heater will also set to "00".
The end of both the Heater Timer and
the Minute Minder Timer is indicated by
the buzzer sound, this can be stopped by
pressing any button.
Key Lock
The key lock function is used to set 'safe
mode' on the appliance and can only be
used in Operating Mode (B-Mode). The lock
function becomes active when the key Lock
button
is pressed for at least 2 seconds.
This operation is acknowledged by a buzzer
and the Key Lock Indicator will flash to
indicate the heater is locked.
If the heater is locked, it will only be
possible to switch the appliance off by
pressing
and it will not be possible to make any
adjustments by pressing the buttons. If any
other button is pressed in the lock mode,
the buzzer will sound and the Key Lock
Indicator will flash.
Only the switch-off operation by pressing
is possible. However, if the appliance is
switched off, it can not be restarted again
without being unlocked.
Child Lock
The child lock function is used to lock
the appliance in a complicated multi-step
process. Child lock (and unlocking) is only
available in the S-Mode.
First,
must be pressed until the buzzer
sounds, then
simultaneously for at least 0.5 seconds,
but no longer than 1 second. Following
this, press
All four heater displays will show "L" as
confirmation.
If the minute minder timer is still running,
it will proceed until "00" is reached and
the timer will beep. After confirmation of
timer completion, the appliance will be fully
locked. None of the buttons can be used as
long as the appliance is locked.
EN - 17
, all other buttons are blocked
and
must be pressed
to activate the child lock.
Publicidad
