Publicidad
Operating Instructions
English
~WARNING
This symbol means important
instructions. Failure to heed them can
result in serious injury or death.
WHEN USING A CAMERA SYSTEM, THE DRIVER MUST
VISUALLY CHECK ACTUAL CONDITIONS AROUND
THE VEHICLE. MAKE SURE THERE ARE NO PERSONS
OR ANIMALS IN THE AREA IN WHICH YOU ARE
MANOEUVRING OTHERWISE YOU COULD INJURE
THEM.
A camera
assists the driver
by sending images
to
the screen
showing conditions in view of
the
camera.
The
camera
uses
a wide-angle
lens. Therefore, there is
a
differen
ce
in
distance
perspective
between what
is normally
seen
and
what
appears on
the
screen. Also,
the
images shown by
the
rearview camera are reversed, so as
to
appear
the
same as
what is seen
through
the
rearview mirror.
The
camera
may not perform to full
capability
due to
variables such as:
weather conditions such as
hard
rain, snow,
fog
or
mud
extremely
high
or low temperatures
near camera
slope of vehicle and/or roadway
direct exposure to very bright
light
such as
headlamp
or bright
sunlight
moving
from very dark to very bright
light
and vice versa such
as
in
parkin
g garages or
tunn els
extremely
low light
areas
walls or objects that are
located
diagonally
in
relation to the
camera
retracted mirrors that change camera viewing angle
open
doors
or trunks
changes
to height
of vehicle
due
to
loading
capacity or
hydraulic
suspensions
obstacles
located
at
the
corner of
the
vehicle
DO NOT DISASSEMBLE OR ALTER.
Doing
so
may result
in an accident, fire or electric shock.
KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS
OUT OF THE REACH OF CHILDREN.
Swallowing them
may
result
in
serious
injury.
If
swallowed,
consult a
Doctor
immediately.
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do
so
may
result in
fire
or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
( Check with your
dealer if
you are
not
sure.) Failure
to do
so
may result
in
fire, etc.
BEFORE WIRING, DISCONNECTTHE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do
so
may result
in electric shock or
injury due
to
electrical shorts.
DO NOT USE BOLTS OR NUTS IN THE BRAKE
OR STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts
or
nuts used
for
the brake
or steering systems ( or
any
other safety-related system), or
tanks
should NEVER be
used for
installations or ground connections. Using such
parts
could
disable
control of
the
vehicle and cause
fire
etc.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When
drilling
holes in the
chassis for
installation, take
precautions
so
as not to
contact,
damage
or obstruct
pipes,
fuel lines, tanks
or electrical wiring. Failure
to take
such
precautions may
result in
fire.
MINIMISE DISPLAYVIEWINGWHILE DRIVING.
Viewing
the display may
distract
the
driver
from looking
ahead of
the
vehicle and cause an accident.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut
away
cable
insulation to
supply
power to
other
equipment.
Doing
so will exceed the current carrying
capacity of
the
wire and result
in fire
or electric shock.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE
OPERATION,
SUCH AS THE
STEERING WHEEL OR GEAR LEVER.
Doing
so may obstruct
forward
vision or
hamper
movement
etc. and results
in
serious accident.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables
in
compliance
with the manual
to prevent
obstructions when
driving.
Cables or wiring
that
obstruct or
hang up
on
places
such as
the
steering wheel,
gear lever,
brake pedals,
etc. can
be
extremely
hazardous.
DO NOT ROUTE ELECTRICAL CABLES NEAR HOT OR
MOVING PARTS
Route the
cables and wiring away
from hot
or
moving
parts,
and
fix
them securely
to avoid heat/mechanical
damage to the
cable
insulation,
which may
result in
shortcirc uit,
fire
or electric shock.
MAKE THE CORRECT CONNECTIONS.
W hen making connections
to the vehicle's
electrical
system, be aware of the factory
installed
components ( e.g.
on-board computer).
Do not tap into these
leads
to provide
power for this unit.
When connecting the
device to
the
fuse
box,
make
sure
the fuse
for
the intended
circuit of
the device has
the appropriate amperage.
Failure
to
do
so
may result in
fire or damage
to the
unit and/or
the
vehicle.
When in
doubt,
consult
your Alpine dealer.
USE THIS PRODUCT FOR MOBILE 12 VOLT
APPLICATIONS.
Use for other
than its designed
application
may result in
fire,
electric shock or other
injury.
CHECK THAT THE CAMERA MOUNTINGS IS ATTACHED
SECURELY, AND THATTHE SCREWS ARE TIGHT
BEFORE DRIVING.
Failure to do
so
may result in
an accident.
WHEN INSTALLING OR CHECKING A CAMERA, DO SO
AFTER PARKING THE CAR IN A LEVEL, SAFE PLACE,
TURNING OFF THE ENGINE, AND APPLYING THE
HANDBRAKE.
Failure to do
so
may result in
an accident.
WHEN USING A DRILL TO MAKE A HOLE, TAKE
PRECAUTIONS SUCH AS WEARING GOGGLES SO
FRAGMENTS DO NOT GET INTO THE EYES.
Failure to do
so
may
result
in injury.
~CAUTION
This symbol means important
instructions. Failure to heed them can
result in injury or material property
damage.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The
wiring and
installation
of
this unit requires
special
technical
skill and experience.
To
ensure safety,
always
contact the
dealer
where you
purchased this product
to
have the
work
done.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the
cables
and
wiring
away
from
moving parts
(like
the
seat rails) or sharp or
pointed
edges.
This
will
prevent
crimping and
damage
to the wiring.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.
Be sure
to use
only
the
specified
accessory parts.
Use
of other
than designated parts may damage this unit
internally
or
may not
securely
install the unit in place. This
may
cause
parts to
become loose resulting
in hazards
or
product
failure.
CONNECT LEADS PROPERLY
Be sure
to
connect
the
colour coded
leads
according
to
the diagram. Incorrect
connections may cause
the unit
to malfunction
or cause
damage to the
vehicle's electrical
system.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do
so
may
cause
personal injury
or damage to
the product. Return it to your
authorized Alpine
dealer
or
the nearest Alpine Service Center for
repairing.
EXCEPT FOR THE
CAMERA,
DO NOT ATTACH ANY
PARTS TO AREAS WHICH WILL GET WET, OR WHERE
THERE IS A LOT OF HUMIDITY OR DUST.
Failure to do
so
may result
in fire or
damage.
DO NOT ATTACH THE CAMERA TO FLUOROCARBON
RESIN FINISHED CAR BODIES OR GLASS.
Doing
so
reduces the
strength of the camera's mounting.
This
could
cause
it to
fall
off
and cause
injury
or
damage to the
car's body.
DO NOT ATTACH THE CAMERA TO ANY SURFACE
WHERE THE ENTIRE ADHESIVE SURFACE CANNOT BE
APPLIED.
Doing
so
reduces the
strength of
the
camera's
mounting.
This
could
cause
it to
fall off and cause injury or
damage to the
car's body.
NOTICE
About
Care
of Device
Do not
assert any excess pressure to the camera or
the
mounting,
as
this
cou ld cause
the
camera direction
to
shift, or
the
camera mounting
bracket
to
come
off.
To
prevent the camera lens, mounting and
cords
from changing
co
lour
or shape, or from
deteriorating,
wipe with a
chemical-
free, damp cloth.
Do not use
an automatic car wash or
high
-pressure
washer.
Doing
so could cause
the
camera
to
come off,
damage
to
the
device cord, or
may
allow water
to enter the
camera or the
inside
of the car.
In
some cases,
to
attach the device, a
hole must
be drilled
in
the
car
body, requiring
use of touch-up paint (retail product) for
rust-prevention,
and should be prepared beforehand.
Be sure
to
disconnect
the
cable from the (-) battery post before
installing your
HCE-C2
IO0RD/HCE-C2600FD. This
will reduce
any chance of
damage
to
the
unit
in
case of a short-circuit.
Be
sure
to
connect the co lour coded
leads
according
to
the
diagram. Incorrect connections
may
cause
the
unit
to
malfunction
or
damage to the
vehicles
electrical
system.
When
making
connections to
the
vehicles
electrical
system,
be
aware of the factory
installed
components (e.g. on-board
computer).
Do not
tap
into
these leads
to
provide power for
this
unit. When connecting the
HCE-C2
100RD/HCE-C2600FD to
the
fuse
box,
make sure
the
fuse for the
intended
circuit of
the
HCE-C2 100RD/
HCE-C2600FD has
the appropriate
amperage.
Failure
to do so
may
result
in
damage
to the unit
and/or
the
vehicle. When
in
doubt, consult your Alpine dealer.
About Rear
Camera
The
rear
camera
is
optimized for
use in
this
system.
as a
dedicated product,
it
should
not
be used
in
other systems.
About Power
Connection
Connect the
reverse
input
wire (orange/white)
to
the power
wire of
the
reverse lamp. Consult your Alpine
dealer
for details.
Confirm that this connection
is made
to
the negative
side of the
reverse
lamp.
Do not
use mobile
phones
and
wireless devices
near
the
camera.
Doing
so
may
result
in noise
on
the
screen or
malfunction. It is
recommended to use mobile
phones or wireless devices away
from the
camera.
About
Camera
Installation
Location
Before installing, make
sure there
is
a enough space
to
be able
to
install the
camera.
If
possible,
install the
camera
in the
center of
the bumper.
If the
camera
is installed
off-center,
the image may
differ from
the
actual
view.
Calibration
is necessary.
Confirming
the Display Function
To
connect
the unit,
confirm
that the monitor
will require a
compatible
RCA
pin
jack.
Publicidad
