Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
GENERAL SPECIFICATIONS
• Shell material: PC/ABS composite
• Standards: These Klein Tools Safety Helmets comply with Type 2
• CLASS E (Non-Vented): ANSI/ISEA Z89.1-2014 (R2019),
tested up to 20kV.
• CLASS C (Vented): ANSI/ISEA Z89.1-2014 (R2019).
EN397:2012+A1:2012 (Clauses listed only):
• 5.2.1
Shock at Very Low Temperature
–
• 5.2.4
Lateral Deformation (LD)
–
• 5.2.5
Molten Metal Splash
–
EN12492:2012 (Listed clauses only):
• 4.2.1.2
Front Energy Absorption Capacity
–
• 4.2.1.3
Side Energy Absorption Capacity
–
• 4.2.1.4
Rear Energy Absorption Capacity
–
• 4.2.2
Resistance To Penetration
–
• 4.2.3
Retention System Strength
–
• 4.2.4
Retention System Effectiveness (roll off)
–
• Fits: Head Sizes 6-1/2 to 8 (20-1/2 to 25 inches / 52 to 64 cm)
SYMBOLS ON PRODUCT (FIG. A)
1
Compliant Standards, Class, Type, and Head Size information
2
Date of manufacture
3
Recycling Code and material type
WARNING LABELS (FIG. B)
There are warning labels
4
affixed to the inside of this safety
Read, understand, and follow these instructions to ensure
helmet.
safe operation. DO NOT REMOVE THESE LABELS.
WARNINGS
READ ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE WARNINGS
AND INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY OR
DEATH.
• This safety helmet provides LIMITED protection from small
objects striking top, front, back, left and right sides of the safety
helmet.
• DO NOT expose safety helmet, EPS insert, suspension, padding and
chin strap to open flame.
• ELECTRICAL WARNING: Avoid areas where the chance of electrical
shock exists. Non-vented versions meet Class E requirements by
providing limited electrical protection. Class C vented models provide
no electrical protection. (See WARNING LABELS Section).
• If the safety helmet or EPS insert has sustained an impact, dispose
of it IMMEDIATELY, even if damage is not visible.
• NEVER alter, puncture, modify or engrave the shell, EPS insert,
suspension or chin strap.
• DO NOT use paints, solvents, chemicals, insect repellent,
adhesives, gasoline or like substances on this safety helmet –
doing so can lessen the protection offered against impact and
penetration.
• DO NOT use this safety helmet as a vehicular or recreational safety
helmet.
• DO NOT store objects between the suspension and the shell, as
the safety helmet will not function as intended and can lessen the
protection from impact and penetration.
• Exposure to direct sunlight, corrosive environments, and/or
extreme temperatures below -40°F (-40°C) or above 120°F (49°C)
can lessen the ability of the safety helmet to withstand impact and
penetration.
MAINTENANCE
SAFETY HELMET CLEANING AND STORAGE
• Clean the safety helmet and suspension with mild soap and water
only. Rinse and wipe dry. Clean chin strap with damp cloth only.
Store in a cool place.
• See SWEATBAND AND TOP COMFORT PAD section of the
operating instructions (on other side) for additional maintenance
information.
INSPECTION AND REPLACEMENT
Inspect the safety helmet, EPS insert, including the suspension, chin
strap and shell, before and after each use:
• Check the Safety helmet's shell for any cracks, breakage,
discoloration, chalky appearance, or any other damage, excessive
wear or unusual condition. These conditions may indicate reduced
impact or penetration resistance and the Safety helmet must be
replaced IMMEDIATELY.
• The suspension and chin strap should be checked for cracks,
breaks, damaged stitching or any other damage, excessive wear
or unusual condition. If any of these conditions exist, they must be
replaced IMMEDIATELY.
• Always use genuine Klein Tools replacement parts. This product
works as a system, and use of unauthorized suspensions and
chin straps may reduce the protection you receive from this safety
helmet.
USEFUL LIFE
SUSPENSION AND CHIN STRAP: Must be replaced after no more
than 12 months of use.
ENTIRE SAFETY HELMET: Entire Safety helmet should be replaced
after 2 years of use, or no more than 5 years from the date of
manufacture, whichever comes first.
These are useful service life guidelines. Regular inspection as
detailed in the MAINTENANCE section above MUST be performed,
and may result in possible earlier replacement.
NOTE: This replacement schedule is a guideline that assumes
normal use and storage conditions for the safety helmet. If the
safety helmet is exposed to temperature extremes, persistent
sunlight, or chemicals, replacement may be required in a shorter
time frame.
WARRANTY
www.kleintools.com/warranty
ACCESSORIES AND REPLACEMENT PARTS
Klein Tools safety helmet accessories and replacement parts
are available online or at major distributors:
• 56048: Rechargeable Auto-Off Headlamp (Spot/Flood)
• 56049: Rechargeable Light Array Headlamp (Flood only)
• 56062: Rechargeable Headlamp / Worklight (Spot/Flood)
• 56063: Safety Lamp
• 60155: Hard hat/Safety Helmet Cooling Fan
• CLMBRSPN: Replacement 6-Point Suspension
• CLMBRSTRP: Replacement Chin Strap
• KHHSWTBND: Sweatband (3-pack)
• KHHSWTBND2: Premium Sweatband (3-pack)
• KHHTOPPAD: Top Comfort Pad (3-pack)
• KHHTOPPAD2: Premium Top Comfort Pad (3-pack)
• VISORCLR: Clear Visor
• VISORGRAY: Tinted Gray Visor
NOTE: KLEIN TOOLS CANNOT GUARANTEE THAT THIRD-PARTY
ACCESSORIES WILL PERFORM OR FIT OPTIMALLY WITH KLEIN
TOOLS SAFETY HELMETS.
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069 1-800-553-4676
customerservice@kleintools.com
FEATURE DETAILS (FIG.C)
Washable top comfort
5
13
Universal accessory slots
pad
6
14
Klein Tools accessory slots
Suspension straps
Vents with shutter
7
15
Re ective stickers
(Class C only)
8
16
Pivot adjustment
Suspension bracket
9
17
Size adjustment knob
Bracket key
10
18
Rear neck pad
Bracket key slots
Suspension strap
11
19
EPS Insert
anchor slots (×6)
12
Washable sweatband
FITTING (FIG. D)
All safety helmets come with suspension pre-installed at factory
settings. The suspension can be adjusted to ensure proper and secure
fit to your head for maximum protection. Follow the steps below:
STEP 1: Turn the size adjustment knob
9
the fit. Position the rear pad on the back of your head, closer to the
neck. Dress any bandana knots or ponytails over the rear neck pad
STEP 2: Tighten by turning the size adjustment knob
until the safety helmet is comfortable and snug. Move your head up,
down and side-to-side gently, like you would normally, and make
sure the safety helmet stays on. Make sure that the safety helmet is
not angled forward or backward, but rests level on your head.
SUSPENSION ADJUSTMENT (FIG. E)
If the safety helmet does not fit properly at the factory settings, you
can further adjust the fit:
STEP 1: Free the suspension by turning the suspension bracket
approximately 90 degrees to free the bracket key
16
bracket key slots
.
18
STEP 2: Determine which slot
you want to reattach to. Using the bracket
18
slots deeper in the safety helmet will move it higher on the head and vice
versa. Insert the bracket key
and turn the bracket
17
degrees to lock into place. Always match the settings on the left and right
sides to prevent the suspension from sitting at an angle.
STEP 3: Verify the safety helmet fits properly. Follow the steps in
the FITTING section to ensure proper fit. Ensure that accessories
you plan to use fit and function properly while maintaining the
safety helmet's ability to perform its function optimally. Check with
a qualified safety expert, if unsure.
NOTE: The suspension strap lengths are xed and cannot be
adjusted. DO NOT attempt to alter.
CHIN STRAP ADJUSTMENT / REMOVAL (FIG. F1, F2, F3)
The safety helmet comes with the chin strap pre-installed.
TO ADJUST CHIN STRAP:
STEP 1: Close the chin strap, adjust the leather portion of the strap
through the clasp loop. Try on the safety helmet and readjust until
the strap is snug between your chin and neck.
STEP 2: Adjust both side "V" brackets up or down for final
adjustment. Ensure both sides of the "V" straps are even, as shown
in FIG. F1.
TO REMOVE CHIN STRAP:
STEP 1: Insert a small blunt-nosed tool (such as long-nosed pliers)
into the round opening to press the release tab as shown in FIG. F2.
STEP 2: Gently pull the strap to begin removing the tab from the
slot. The tab will not come out completely in this step. Once the tab
catches, stop pulling. DO NOT attempt to forceably remove.
STEP 3: Press the exposed portion of the release tab as shown in
FIG. F3 while gently pulling on the strap to release the tab from the
slot.
Repeat process at all remaining attachment points.
NOTE: Check with your Safety Supervisor prior to removing your
chin strap, as it may be required at all times on your jobsite.
SWEATBAND AND TOP COMFORT PAD (FIG.H)
Klein Tools safety helmets come with an advanced sweatband and
top comfort pad designed to wick away sweat. They are machine
washable in a normal wash cycle. DO NOT wash with bleach or with
detergents containing bleach. Machine dry on normal or low heat
setting only.
The sweatband and top comfort pad can be easily removed and
reinstalled on the suspension:
• The top comfort pad is held in place by a single hook-and-loop pad
.
25
• The sweatband is held in place by four suspension hooks
three hook-and-loop pads
simply detach all hook-and-loop pads and slide the sweatband off
the suspension hooks.
www.kleintools.com
Klein Tools Class C safety helmets have vents and shutters on both
sides. The vents can be adjusted by simply sliding the shutter tabs
up or down.
7
The vents and shutters will NOT prevent vapors, liquids, or
debris smaller than the vents from entering the safety helmet.
The optional 56062 is a rechargeable headlamp designed
specifically for Klein safety helmets that have the integrated front
and rear accessory slots. It functions as a spot light or flood light,
and has magnet to attach onto magnetic surfaces for use as a
worklight. Charging cable is included with models that include
rechargeable headlamps.
19
Release tab
20
On/Off/Mode button
21
Spot light
The 56062 can be attached to both the front and back of the helmet
counterclockwise to loosen
via the Klein Tools accessory slot. It can be tilted up to 64 degrees
on the safety helmet and standalone as a worklight.
.
10
To install the headlamp onto a Klein safety helmet, align the
clockwise
9
pivoting mount
safety helmet and push down until the headlamp clicks securely
into place.
To remove the headlamp, press forward on the Release Tab
lift the headlamp out of the accessory slot.
Klein Tools Type 2 safety helmets come with reflective stickers
factory-installed. DO NOT remove or reposition these stickers on the
safety helmet.
from the
17
WARNING: Klein Tools DOES NOT approve the application of
stickers, hot stamps, inks, and foils that have metallic content
to this hard hat by end users. Such modi cations can alter the
performance of the hard hat.
approximately 90
16
Optional visors specially designed to mount
Safety Helmets are also available, in clear and tinted gray. See
ACCESSORIES AND REPLACEMENT PARTS section for available
models.
, on the side and front. To remove,
25
VENTS (C-CLASS ONLY)
56062 HEADLAMP (FIG.G)
22
Flood lights
23
Magnet
24
Pivoting mount
with the Klein Tools accessory slot
24
6
REFLECTIVE STICKERS (FIG. C)
VISORS
onto Klein Tools
27
and
26
on the
, and
19
15
Publicidad
