Health Zenith SL-5650 Instrucciones De Instalación

Mercury Vapor Dusk to Dawn 175W Security Light
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.
NOTE: All wiring must be run in accordance with the National Electrical Code through conduit or another acceptable means. Contact
a qualified electrician if there is any question as to the suitability of the system.
Photocontrol
Lens/Reflector
Assembly
To test operation during daylight, cover the photocontrol with a small box. Turn on the power. Not all photocontrols are alike. Some may
have a time delay of a few minutes, others will turn on as soon as power is applied. The light will take up to ten minutes to reach full
brightness. Uncover the photocontrol and your unit will operate automatically—on at dusk, off at dawn.
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.
Light bulbs are not covered. To obtain a refund or a replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered by
this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does
not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a customer
uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION
OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN
LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA
SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO
ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.
© 2003 DESA Specialty Products™
Installation Instructions
Ground Screw
Cover Plate
Fixture Wires
Thru This Hole
ONE YEAR LIMITED WARRANTY
CAUTION: Make sure the power is off before starting the
installation.
1. Select a location on a flat wall with structurally sound wood
and from 10 to 25 feet (3 to 7.6 m) from the ground. The wood
should be at least one inch thick to safely secure the fixture.
2. Using the mounting template as a guide, mark the 3 mounting holes.
We suggest drilling 3/16" (4.8 mm) pilot holes for the lag screws.
3. Install the two bottom lag screws first. Screw in the lag screws
so that there is about 3/8" (9.5 mm) of space under the head.
4. Place the fixture on these two screws and install the top lag
screw. Tighten the top lag screw first, then tighten the remain-
ing lag screws.
5. Secure your outdoor cable or flexible conduit to the cover plate
with a fitting in accordance with the National Electrical Code.
6. Thread the black and white fixture wires through the hole in
the cover plate as shown.
7. Connect the fixture wires to the service wires (black to black
and white to white).
8. This fixture must be connected to ground. Secure the service
ground wire under the head of the green ground screw.
9. Install the cover plate. Secure with the two screws and nuts
provided.
10. Install the reflector/lens assembly. Secure with the two screws
and washers provided.
11. Screw in the 175 watt mercury vapor type H39 lamp provided.
12. Loosen the screw in the center of the photocontrol socket two
turns. Twist the socket so that the arrow points north. Note:
There is a stop to prevent the socket from turning all the way
around. If you have trouble turning the socket, try turning it the
other direction. Retighten the screw in the center of the socket.
13. Align the photocontrol with the socket (it will only plug-in
one way). Plug it in and twist clockwise until it stops. If
photocontrol is already installed, turn clockwise to ensure that
it is locked in place.
Model SL-5650
598-1088-03