ASROCK DeskMeet X300 Serie Guía De Instalación Rápida

Package Contents
Quick Installation Guide
DeskMeet X300 Series
DeskMeet X300 series
* e barebone system does not
include memory, hard drive,
WiFi module and M.2 SSD.
SATA Cable
*15G067042000AK*
P/N: 15G067042000AK
Front View Rear View
後視圖 / Rückansicht / Vue arriere / Retrovisore / Vista trasera /
前視圖 / Vorderansicht / Vue de face / Visione frontale / Vista frontal
Передний план / Vista frontal/ 전면보기/正面図 Вид сзади / Visão traseira / 배면도 /背面図
Headphone/Headset Jack
LAN RJ-45 Port
USB 3.2 Gen1 Type-C Port
USB 3.2 Gen1 Type-A Ports
USB 2.0 Ports
Power Switch
AC Power
Connector
主機板構造圖 / Motherboard-Layout / Carte mère / layout della scheda madre / tarjeta madre /Материнские платы Макет
Motherboard Layout
Disposição da placa-mãe / 메인 보드 레이아웃 / マザーボードのレイアウト
Top View
Key E 2230 M.2 Slot 6
(for WiFi + BT Module)
Key M 2280 M.2 Slot (M2_1)
(support M.2 PCIe SSD up to Gen3 x4)
SATA3 Connectors
Clear CMOS Jumper
Key E 2230 M.2 Slot
(CLRMOS1)
(for WiFi + BT Module)
Chassis Fan Connector
8
(CHA_FAN1)
System Panel Header 7 USB 2.0 Header 6
(PANEL1) (USB_5_6)
Onboard Connectors 主機板元件 / Onboard-Anschlüsse / Connecteurs à bord / Connettori a bordo / Conectores a bordo / Бортовые соединители
Conectores de bordo / 온보드 커넥터 / オンボードコネクタ
3 CPU Fan Connector ATX Power Connector
1 COM Port Header (COM1) 5
(CPU_FAN1) (ATXPWR1)
1
RRI#1 1
GND
CCTS#1 1
RRTS#1 2 +12V
DDSR#1
GND
3 CPU_ FA N_SPEED
DDTR#1
TTXD#1 FA N_SPEED_CONTROL 13
4
RRXD#1
DDCD#1
USB 2.0 Header
8 pin 12V Power Connector 4 Chassis Intrusion Header 6
2
(USB_5_6)
(ATX12V2) (CI1)
1
8 5
U SB_PW R USB_PWR
GND 1
P- P-
Signal P+
P+
4 1
GND GND
DUMMY
Screw Package
Foam Pad for Power Supply
ATX Power Supply
PWR Screw x 4pcs PCIe Card Screw x 2pcs
(Step Screw x 2pcs included)
2.5" HDD/SSD Screw x 8pcs 3.5" HDD Screw x 9pcs (Countersunk Screw x 2pcs included)
Quick Installation Guide
Customization Options
M.2 WiFi kit
Screw Package
Rubber Foot x 4pcs, M.2 Screw x 3pcs, 2.5" HDD/SSD Screw x 8pcs,
3.5" HDD Screw x 9pcs (Countersunk Screw x 2pcs included),
PWR Screw x 4pcs (Step Screw x 2pcs included), PCIe Card Screw x 2pcs,
Foam Pad for Power Supply
Hardware Installation
Begin Installation
A
Line out Jack
USB 3.2 Gen1 Ports
USB 2.0 Ports
HDMI Port
D-Sub Port
DisplayPort
1. Remove the screw from the bottom
side of the case.
Installing the CPU
B
1
COM Port Header (COM1) 1
(for X300-ITX/COM only)
1
8 pin 12V Power Connector
2
(ATX12V2) 1
AMD AM4
CPU Socket
Installing the CPU Fan and Heatsink
C
CPU Fan Connector 3
(CPU_FAN1)
Installing the CPU Box Cooler -1
4 x 288-pin DDR4 DIMM Slots
(DDR4_A1, DDR4_B1)
4 x 288-pin DDR4 DIMM Slots
1
(DDR4_A2, DDR4_B2)
Chassis Intrusion Header 4
4
(CI1) 1
ATX Power Connector 5
(ATXPWR1)
System Panel Header
7
(PANEL1)
1
HDLED+ PLED+
12
HDLED- PLED- 2
PWRBTN#
GND
24
RESET# GND
GND
Chassis Fan Connector
8
(CHA_FAN1)
1 GND
2 +12V
3 CHA_ FA N_SPEED
4 FA N_SPEED_CONTROL
*For more details on the CPU Cooler installation, please refer to the user manual.
Rubber Foot x 4pcs
M.2 Screw x 3pcs
Attach the foam pad to this position of the power supply
to avoid damaging the case.
客製化選擇 / Anpassungsoptionen / Options de personnalisation / Opzioni di personalizzazione / Opciones de personalización /
Настройка параметров / Opções de personalização / 사용자 지정 옵션 / カスタマイズオプション / 客制化选择
DeskMini Addressable LED DeskMini USB HUB
硬體安裝 / Hardware-Installation / Installation du matériel / Installazione hardware / Instalación de hardware / Установка оборудования
Instalação de hardware / 하드웨어 설치 / ハードウェアのインストール / 硬件安装
2. Pull out the motherboard tray. 3. Remove the PSU and EPE Sponge.
2 3
3
4
Installing the CPU Box Cooler -2
1
3
D Installing Memory Modules
1
* e DeskMeet X300 series requires DDR4 DIMM.
*For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 DIMM pairs.
Installing the M.2 WiFi/BT Module and WiFi Antennas
E
1. Insert the WiFi/BT module into the M.2 slot. 2. Tighten the screw to secure the module
5
4. Insert the SMA Wi-Fi Antenna Cables to the
designated holes. Make sure that the cable routing
is organized as shown in the illustration above.
F Installing the Type 2280 Ultra M.2 SSD
1. Locate the M.2 slot on the motherboard.
2
3
4
2 3
3. Attach the SMA Wi-Fi Antenna Cables to the
to the motherboard. module.
5. Insert the Wi-Fi Antenna Connectors 6. Fasten the screw nuts to secure the
to the antenna ports on the rear panel antenna connectors..
2. Carefully insert the M.2 SSD into the slot. 3. Tighten the screw to secure the M.2 SSD
to the motherboard.