Publicidad
Idiomas disponibles
Idiomas disponibles
transport and that all parts are in the packing box.
In case of loss or anomaly, contact your dealer im-
mediately.
- Remove all plastic protections.
- Save all packing materials until you have satisfactorily
inspected and used the tool.
The device comes partially assembled.
The following components must be installed before
starting the device:
- Filtration casing (A)
- Machine connection tube (B)
- Suction/collector connection tube (C)
- Fan and motor (D)
- Engine support (E)
- Outlet adapter with rubber gasket (F)
- Transport wheels (G)
- Inlet adapter (F)
- Base plate (I)
- Stopper (J)
- Supports (K)
- Filter bag support (L)
- Filtration bag (M)
- Recovery Bag (N)
5.2 ASSEMBLY OF THE BASE PLATE (Fig. 5 and 6)
Tools needed: 1 screwdriver + 1 10 mm wrench (not
included).
Check the flatness of the floor. The device
must be absolutely stable.
- Place the edge plate (21).
- Place the rollers (22) under the table and secure with
4 sets of M6x10 Cross Head Screws / Washer / M6 Nut
(23) each: insert the screws from the top of the table,
then the washers and nuts from below.
- Tighten the screws and nuts (23) well and then turn
the plate (21) over.
5.3 MOUNTING ON THE BASE PLATE (Fig. 7 to 10)
Tool required: 1 x 13 mm wrench (not included).
Don't carry the motor alone - get help
lifting, moving and positioning it!
- Place the motor support (24) on the plate (25) (Fig. 7)
and screw it directly onto the plate with the 4 M8x16
hexagonal screws and the washers (26) (Fig. 8).
- With the help of a third person, place the fan/motor
assembly (27) on the plate (25): the motor must rest on
the support (24) and the fan mounting brackets must
be placed in the 2 holes (28 ) (Figs. 7 and 8).
- Adjust the position of the fan (27) and then secure it
with 2 sets of M8x16 Hex Washers / Screws (29) which
you will screw directly into the plate (25) (Fig. 9).
- Adjust the position of the motor (27) and then fix it on
its support (24) with 4 sets of M8x25 hexagonal screws
/ washers / M8 nut (30) (Fig. 10).
5.4 ASSEMBLY OF THE OUTLET ADAPTER (Figs.
11 to 17)
Tools needed: 1 10 mm wrench + 1 13 mm wrench
(not included).
- Place the gasket (31) on the fan outlet (32) (Fig. 11).
- Then fit the output connector (33) correctly positioning
the gasket (31), then secure it with 6 sets of M6x20
hexagonal screws/washers/M6 nuts (34) (Fig. 12).
- Position the manifold supports (35) and fix them with
2 sets of M8x16 hexagonal screws each / washer (36)
that you will screw directly onto the plate (37) (Fig. 13).
Take care to correctly orient the supports (35) so that the
manifold fixing lugs face the inside of the plate (Fig. 14).
Don't install the filter housing alone – get
help lifting, positioning and securing it!
- With the help of a third person, place the filter casing
(38) on top of the supports (35) directing the inlet (39) of
the filter casing towards the motor/fan assembly (Fig. 15).
- Fix the filter housing (38) on the 2 external supports
(35) with for every 2 sets of M8x16 hexagonal screws
/ washer (40) that will screw directly on the filter
housing (Fig. 16).
- Position the filter bag support bracket (41) on the
central support bracket (35) (Fig. 17).
- Screw everything directly to the filter housing (38)
with 2 sets of M8x16 hexagonal screws/washers (40).
5.5 ASSEMBLY OF THE FLEXIBLE TUBE Ø 125 mm
(Fig. 18 and 19)
Tool required: 1 10 mm spanner or 1 flat screwdriver
(not supplied).
- Place one of the 2 clamps (42) at one end of the Ø
125 mm tube (43) (Fig. 18).
- Mount the tube (43) on the fan outlet connector (44),
then tighten the collar (42).
- Place the second collar (42) at the other end of the Ø
125 mm tube (43) (Fig. 19).
- Fit the tube (43) on the manifold inlet (45) and then
tighten the collar (42).
5.6 ASSEMBLY OF THE INLET CONNECTOR AND
FLEXIBLE TUBE (Fig. 20 and 21)
Tools required: 1 screwdriver + 1 10 mm spanner or 1
flat screwdriver (not supplied).
15
Publicidad
