VONROC PM508DC Traducción Del Manual Original página 7

accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the hou-
sing and excessive accumulation of powdered
metal may cause electrical hazards.
o) Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
p) Do not use accessories that require liquid cool­
ants. Using water or other liquid coolants may
result in electrocution or shock.
q) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can
entangle your fingers or snag on the workpiece.
r) Do not press the spindle lock until the tool stops.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or any
other accessory. Pinching or snagging causes rapid
stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory's rotation at
the point of the binding. For example, if an abrasive
wheel is snagged or pinched by the workpiece, the
edge of the wheel that is entering into the pinch
point can dig into the surface of the material cau-
sing the wheel to climb out or kick out. The wheel
may either jump toward or away from the operator,
depending on direction of the wheel's movement
at the point of pinching. Abrasive wheels may also
break under these conditions. Kickback is the
result of power tool misuse and/or incorrect opera-
ting procedures or conditions and can be avoided
by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and po­
sition your body and arm to allow you to resist
kickback forces. Always use auxiliary handle,
if provided, for maximum control over kickback
or torque reaction during start­up. The operator
can control torque reactions or kickback forces,
if proper precautions are taken.
b) Never place your hand near the rotating acces­
sory. Accessory may kickback over your hand.
c) Do not position your body in the area where po­
wer tool will move if kickback occurs. Kickback
will propel the tool in direction opposite to the
wheel's movement at the point of snagging.
WWW.VONROC.COM
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of shortcircui-
ting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
c) In case of damage and improper use of the bat­
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type rechar-
geable Battery packs with the charger. Other types
of batteries may burst causing personal injury and
damage.
a) The appliance is not to be used by persons
(including children) with reduced physical, sen­
sory or mental capabilities, or lack of experien­
ce and knowledge, unless they have been given
supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging non­rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
EN
7