Wesco WS2942 Manual De Instrucciones página 11

OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction book
carefully.
1. CHARGING
WARNING! The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never
insert or allow metallic objects into your charger or
battery pack connections because of an electrical
failure and hazard will occur.
BEFORE PUTTING INTO OPERATION
A) CHARGING THE BATTERY (SEE FIG. A)
NOTE:
a) Do not use any charger other than that specifically provided for
use with the equipment.
b) If the battery pack is very hot you must remove your battery pack
from the charger and allow time for the battery to cool down
before recharging.
c) The battery in your new tool is not charged when it leaves the
plant. Therefore it must be full charged before using the first time.
d) Please charge the battery to reach full or no less than half charge
before storage. If the tool will not be used for long periods of time,
charge the battery every 3-6 months.
CHARGING PROCEDURE
1) Plug the charger into an appropriate outlet. The light will be green.
2) Slide the battery pack into the charger, the light will turn to red to
indicate the charging process has started.
3) When charging is completed, the light will turn to green. The pack
is now fully charged, unplug the charger and remove the battery
pack.
WARNING! When battery charge runs out after
continuously use or exposure to direct sunlight or heat,
allow time for the tool to cool down before re-charging to achieve
the full charge.
Light
Red on
Green on
2. ASSEMBLY
ASSEMBLING THE BLOWER TUBE (SEE FIG B1- B2)
1) Align the tab on the Blower Tube with the indentation on the
Blower Port and attach the Blower Tube on Blower Port.
2) Then slightly rotate the tube until it locks into position as shown in
Fig. B2. Make sure the blower tube is firmly assembled.
WARNING! Do not attempt to operate or disassemble the
safety switch by any means other than the normal
assembly.
INSTALLING AND REMOVING THE BATTERY PACK
(SEE FIG. C1-C2)
a) TO INSTALL THE BATTERY PACK
Slide the fully charged Battery Pack onto the tool with sufficient
force until it clicks into position.
b) TO REMOVE THE BATTERY PACK
Press the Battery Pack Release Button firmly first and then slide the
Battery Pack out from your tool.
EN
Status
Charging
Fully Charged
3. OPERATION
INTENDED USE:
The blower is intended for blow debris. It's not intended for use
indoors and animal grooming.
SWITCHING ON AND OFF (SEE FIG. D)
Press the On/off Switch to switch on. Release the On/off Switch to
switch off.
WARNING!The tool runs for approximately 5 seconds
after it has been switched off. Let the motor come to a
complete standstill before setting the tool down.
BLOWING (SEE FIG. E)
When use for blowing, attach the Blower Tube to the Blower Port.
WARNING! Flying debris can cause serious personal
injury to the operator, bystanders or pets. Keep bystanders
and pets at least 5m away from the area of work and always wear
suitable eye and ear protection, long pants and sturdy shoes or
boots whilst operating the tool.
MAINTENANCE
1. Store the tool, instruction manual and accessories in a secure,
dry place. In this way you will always have the information ready.
2. Keep the tool's air vents unclogged and clean at all times.
3. Remove dust and dirt regularly. Cleaning is best done with a rag
or brush.
4. Never use caustic agents to clean plastic parts.
CAUTION: Do not use cleaning agents to clean the
plastic parts of the tool. A mild detergent on a damp cloth is
recommended. Water must never come into contact with the tool.
TROUBLESHOOTING
Possible
Problem
cause
Mains voltage is
not present
Device does not
start
Defective on/off
switch
Defective motor
Damaged battery
pack
Device
Internal loose
works with
connection
interruptions
Defective on/off
switch
Fault correction
Check the battery
pack, charger, where
appropriate, repair
through electrical
specialist
Repair through
customer service
Check the battery
pack, replace it.
Repair through
customer service.
11