Hilti HIT-RE 500 V4 1400 Jumbo Manual Del Usuario página 16

Hilti HIT-RE 500 V4 1400 Jumbo
16
the mixer attached on the foil pack manifold and store under the recommended storage conditions. If reused, attach a new
mixer and discard the initial quantity of anchor adhesive.
q WARNING
q Improper handling may cause mortar splashes. Eye contact with mortar may cause irreversible eye damage! Always wear
tightly sealed safety glasses, gloves and protective clothes before handling the mortar! | Never start dispensing without
a mixer properly screwed on. | When using an extension hose: Discard of initial mortar flow must be done through supplied
mixer only (not through the extension hose). | Attach a new mixer prior to dispensing a new foil pack (snug fit). | Caution!
Never remove the mixer while the foil pack system is under pressure. Press the release button of the dispenser to avoid
mortar splashing. | Use only the type of mixer supplied with the adhesive. Do not modify the mixer in any way. | Never use
damaged foil packs and/or damaged or unclean foil pack holders.
q Poor load values / potential failure of fastening points due to inadequate borehole cleaning. The boreholes must be dry
and free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection. Hilti hollow drill bits
TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction
capacity (volumetric flow rate) as specified in the accessory table. | For blowing out the borehole – blow out with oil free air
until return air stream is free of noticeable dust. | For flushing the borehole – flush with water line pressure until water
runs clear. | Important! Remove all water from the borehole and blow out with oil free compressed air until borehole is
completely dried before mortar injection (not applicable to hammer drilled hole in underwater application). | For brushing the
borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small
and must be replaced. | Inject adhesive immediately after cleaning the borehole. If not, water may come into the borehole
when using wet base material.
q Ensure that boreholes are filled from the back of the boreholes without forming air voids. If necessary, use the accesso-
ries / extensions to reach the back of the borehole. | For overhead applications use the overhead accessories HIT-SZ / IP
and take special care when inserting the fastening element. Excess adhesive may be forced out of the borehole.
Make sure that no mortar drips onto the installer. | If a new mixer is installed onto a previously-opened foil pack, the first
trigger pulls must be discarded.
q Due to the heat generation during curing, metal element (rod) must be set within the allowed working time or wood
(the base material) may be negatively effected.
q Not adhering to these setting instructions can result in failure of fastening points.
[NL Ankermortel voor bevestiging van betonijzer en pluggen in beton/hout
Hilti HIT-RE 500 V4
UFI: 8JUT-00GC-681F-RRDG (A)
UFI: E93U-J0M2-S810-8FU9 (B)
Bevat: 2,2-bis(4-hydroxyfenyl)propaan-bis(2,3-epoxypropyl)ether (A);
butaandioldiglycidylether (A); 2-methyl-1,5-pentanediamine (B); m-Xyleen, α,α'-diamine (B)
GEVAAR Veroorzaakt ernstige brandwonden en oogletsel. (A, B) | Kan een allergische huidreactie veroorzaken. (A, B) | Kan
irritatie van de luchtwegen veroorzaken. (B) | Giftig voor in het water levende organismen, met langdurige gevolgen. (A, B) |
Beschermende handschoenen/beschermende kleding/oogbescherming/gelaatsbescherming dragen. | Contact met de ogen,
de huid of de kleding vermijden. | BIJ CONTACT MET DE OGEN: voorzichtig afspoelen met water gedurende een aantal minu-
ten; contactlenzen verwijderen, indien mogelijk; blijven spoelen. | Bij huidirritatie of uitslag: een arts raadplegen. | Bij aanhou-
dende oogirritatie: een arts raadplegen. | BIJ CONTACT MET DE HUID: met veel water en zeep wassen.
(A, B) (A, B) (A)