Publicidad
Idiomas disponibles
Idiomas disponibles
English
•
Drive fasteners into work surface only.
•
When working close to an edge of a workpiece
or at steep angles use care to minimize chipping,
splitting or splintering, or free flight or ricochet of
fasteners, which may cause injury.
•
Do not drive fasteners on top of other fasteners
or with the tool at an overly steep angle as this
may cause deflection of fasteners which could
cause injury.
•
Do not load tool with fasteners when any one of
the operating controls is activated.
•
Use extra caution when driving fasteners into
existing walls or other blind areas to prevent
contact with hidden objects or persons on other
side (e.g., wires, pipes.)
•
The operator must not pull the trigger except
during fastening operation as serious injury could
result if the tool accidentally contacts someone or
something, causing the tool to cycle.
•
Keep hands and body away from the discharge
area of the tool. The tool may bounce from the
recoil of driving a fastener and an unwanted
second fastener may be driven possibly
causing injury.
•
Check operation of the trigger mechanism
frequently. Do not use the tool if the trigger is not
working correctly as accidental driving of a fastener
may result. Do not interfere with the proper
operation of the trigger mechanism.
•
Never inadvertently pull or grasp the trigger when
moving about, changing work location, when
holstering or hanging tool, or when preparing work
surface for fastening operation.
•
This tool produces SPARKS during operation.
NEVER use the tool near flammable substances,
gases or vapors including lacquer, paint, benzine,
thinner, gasoline, adhesives, mastics, glues or any
other material that is ‑‑ or the vapors, fumes or
byproducts of which are ‑‑ flammable, combustible
or explosive. Using the fastenerer in any such
environment could cause an EXPLOSION resulting
in personal injury or death to user and bystanders.
WARNING: After driving a fastener, tool may
bounce back ("recoil") causing it to move away
from the work surface. To reduce risk of injury
always manage recoil by:
•
Always maintaining control of tool.
•
Allowing recoil to move tool away from
work surface.
•
Not resisting recoil such that tool will be forced
back into the work surface. In "Contact Actuation
Mode, " if workpiece contact is allowed to re‑contact
work surface before the trigger is released, an
unintended discharge of a fastener will occur.
•
Keeping face and body parts away from tool.
4
WARNING: Disconnect tool:
•
When not in use.
•
When performing any maintenance or repairs,
•
When clearing a jam.
•
When elevating, lowering or otherwise moving tool
to a new location.
•
When tool is outside of the operator's supervision
or control.
•
When removing fasteners from the magazine.
WARNING: When maintaining the tool:
•
Always shut off air supply, and disconnect tool from
air supply when not in use.
•
When working on air tools note the warnings in
this manual and use extra care when evaluating
problem tools.
Additional Safety Warnings
WARNING: Do not use this product to fasten electrical
cables. Fastening electric wires / cables could result in
electric shock or serious harm.
WARNING: Make sure there are no electrical cables,
gas pipes, etc. that could cause a hazard if damaged by
use of the tool.
WARNING: This tool is not intended for use in
potentially explosive atmospheres and is not insulated
from coming into contact with electrical power.
•
Do not use the tool as a hammer.
•
Always carry the tool by the handle with hand off
trigger/ triggers.
•
Never lift, pull, lower, or carry the tool by the air hose.
•
Whipping hoses can cause severe injury. Always check for
damaged or loose hoses or fittings.
•
Never direct compressed air at yourself or anyone else.
•
Compressed air can cause severe injury.
•
Do not alter or modify this tool from the original design or
function without approval from PORTER‑CABLE.
•
Never clamp or tape the trigger in an actuated position.
•
Ensure tool is always safely engaged on the workpiece and
cannot slip.
•
Never leave a tool unattended with the air hose attached.
TO PREVENT ACCIDENTAL INJURIES:
•
Never place a hand or any other part of the body in fastener
discharge area of tool while the air supply is connected.
•
Never actuate the tool unless nose is directed at the work.
•
Do not actuate the tool while loading.
•
Keep hands and body parts away from the discharge
area of the tool. While in use NEVER grasp the tool by the
magazine or canister, a mis‑driven fastener can exit the
nose causing injury.
Additional Safety Information
WARNING:Never modify the power tool or any part of
it. Damage or personal injury could result.
Publicidad
