Publicidad
Idiomas disponibles
Idiomas disponibles
INSERTING GLUE STICKS
See Figure 2, page 9.
Use mini 0.28 in. (7.11 mm) diameter glue sticks in this glue
pen. Use Ryobi glue sticks for best performance.
WARNING:
To reduce the risk of injury, the glue pen should be con-
sidered to be HOT whenever the LED on the unit is illu-
minated. Following this rule will reduce the risk of burns,
fire, or serious personal injury.
The LED indicator will light up when a charged battery pack
is installed and the power button has been pressed on.
Make sure the power button is off.
Insert a glue stick through the opening at the back of the
glue pen. Guide the glue stick into the glue chamber until
it will go no further.
Install the battery pack.
Press and hold the power button for three seconds. The
LED will flash green for 30 seconds while glue pen begins
to heat.
NOTE: The LED will remain solid green when the glue pen
is ready for use.
NOTE: Different types of glue sticks will heat to working
temperature at different rates. Always test on a scrap piece
to make sure the glue is at optimum temperature.
Place the glue pen in the stand while heating.
NOTE: The drip tray stand will catch any drips while the
glue pen is heating.
WARNING:
Always place the glue pen so that nozzle does not come
in contact with anything while it is heating or when not
in use. Following this rule will reduce the risk of damage
to items, burns, fire, or serious personal injury.
HELPFUL HINTS FOR USE
Before applying glue to a surface or workpiece, use a
scrap piece of paper or material that is similar to your
workpiece as a test.
Use caution when applying hot glue to thin or porous ma-
terial. The underlying surface could be damaged or glue
could adhere to the surface and be difficult to remove.
Do not force the pen tab when applying hot glue. This
could damage the glue pen. Use a test piece of material
to make sure the glue has melted enough to flow without
forcing.
Apply only as much glue as needed for your application.
OPERATION
When gluing two objects together, do not pick up the
object to which hot glue has been applied. Instead, pick
up the other object and join it to the object to which you
have applied hot glue.
Do not use your fingers to press down on an object to
which hot glue has just been applied. This can cause hot
glue to escape from the edges or heat up the bonding
surface and possibly cause burns or damage to surround-
ing objects.
Allow glue to dry completely before moving your work to
ensure proper adhesion and reduce the risk of burns.
If applying glue to very small objects, use tweezers or
tongs to avoid getting the nozzle close to your fingers.
APPLYING HOT GLUE
See Figure 3, page 9.
Install the battery pack.
Press and hold the power button for three seconds. The
LED will flash green for 30 seconds while glue pen begins
to heat.
NOTE: The LED will remain solid green when the glue
pen is ready for use.
Allow time for the glue to melt so that it flows freely from
the nozzle.
Hold the glue pen firmly, as shown in figure 3. Place the
nozzle close to the surface where glue will be applied.
NOTE: Holding the glue pen too far from the intended
surface may result in applying glue to a surface other than
your workpiece or may result in "strings" of glue between
your work and the nozzle.
Press the tab on either side of the glue pen until glue
flows from the nozzle. Do not over-apply glue.
When the desired amount of glue has been applied,
release the tab. Tilt the nozzle slightly to the side and
carefully pull the nozzle away from the object. This helps
avoid strings of glue clinging to the work.
NOTE: The glue pen will stop dispensing glue when the glue
stick in the chamber is almost used up. Insert another glue
stick into the chamber.
NOTE: The LED will show a solid red when battery charge
is low. The LED will flash red three times before turning off
due to low battery charge.
Always press the power button off when you are finished
using the glue pen. The LED will turn off when the glue
pen is no longer heating.
Set the glue pen on the drip tray stand while the product
cools to catch possible glue drips.
Allow the glue stick and glue pen nozzle to completely
cool before removing the battery pack, and before
storage.
6 — English
Publicidad
