Denver TCU-203 PINK Manual De Instrucciones página 2

LOCATION OF CONTROLS
1. FUNCTION SWITCH
2. VOLUME CONTROL
3. FM TELESCOPIC ANTENNA
4. FOLDING HANDLE
5. AUX IN JACK
6. CD DOOR
7. CD DOOR OPEN AREA
8. DIAL SCALE
9. BAND SWITCH
10. TUNING CONTROL
11. POWER INDICATOR
12. LCD DISPLAY
13. FM ST. INDICATOR
POWER SUPPLY

BATTERY OPERATION
1. Remove the battery compartment cover gently.
2. Install 8 x 'C' size batteries (UM-2 or equivalent) while observing the correct polarities.
3. Replace the battery compartment cover.
NOTE:
 The AC cord must be detached from the AC socket of the player.
 Leaking batteries may damage the battery cabinet and the player as a whole, so they
should be removed from the cabinet when becoming flat or when the player is not to
be played on batteries for some time.

AC OPERATION
Insert the AC cord to the AC socket of the player, and plug the other end to an applicable
wall outlet.
NOTE: If the AC plug of this unit does not fit in with your AC outlet, a plug adaptor should
be used. Consult your local dealer on the type of plug adaptor.
TO PLAY THE RADIO
1. Set the FUNCTION switch to the RADIO position, the POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control (rotate that control back and
forth until you get the strongest and clearest reception).
4. When FM (stereo) station is received, the FM indicator will be lit up.
5. The built-in AM antenna and external FM TELESCOPIC ANTENNA are directional.
 When you are receiving an FM broadcast, fully extend the TELESCOPIC ANTENNA
and rotate it for the best reception.
 For AM broadcast, rotate the whole set until the best reception is heard.
6. Adjust the volume level to a comfortable listening level.
7. To turn off the radio, set the FUNCTION switch to the OFF position.
14. LEFT SPEAKER
15. SKIP/SEARCH DOWN BUTTON
16. SKIP/SEARCH UP BUTTON
17. 10+ BUTTON
18. USB PORT
19. PROG. BUTTON
20. MODE BUTTON
21. STOP/USB BUTTON
22. PLAY/PAUSE BUTTON
23. RIGHT SPEAKER
24. BATTERY COMPARTMENT
25. AC SOCKET
2
HANDLING AND MAINTENANCE OF A DISC
Follow the instructions below to handle and maintain your disc in
order that long time and trouble free performance can possibly be
obtained:
 Ensure not to caress the rain bow side of the disc; handle the
disc by the edge.
 Long time exposure to sunshine, high temperatures and humidity
will damage the disc. And keep storage area clean.
 Avoid sticking labels on both sides of a disc. Writing with pointed
articles on the disc should be strictly avoided.
 Clean the disc wiping the centre and then working out to the edge
with a dry & soft cloth or a disc brush. Avoid any cleansing lotion
or chemical eradicator.
 Store them in their cases when they are not to be used.
LOAD A DISC
1. Open the CD door by the Door open area.
2. Load a disc on the disc tray with the label side facing up.
3. Close the CD door.
PLAY A DISC
1. Slide the Function switch to CD/USB/AUX position.
2. Follow the steps above to load a disc.
3. The player begins reading disc immediately.
4. When the disc is successfully read, total number of tracks shows in the LCD and playback
follows with the first track.
5. Press Play/Pause button once to halt music playback, the track number flashes to
indicate the player in Pause mode; press Stop button to cease music playback. The LCD
shows the total number of tracks again.
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY (CD)
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip to
a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to go back to the beginning of
the current track. Press the SKIP/SEARCH down button twice repeatedly to skip to the
previous track. To skip to a specific track at back, press this button several times.
3. Press 10+ button once in play to skip to the track 10 tracks ahead, twice to skip to the
track 20 tracks ahead. You can reach the last track of the disc using this button.
4. Hold the SKIP/SEARCH up button in music play to search at quick rate for a specific point
to play.
5. Hold the SKIP/SEARCH down button in music play to search at quick rate for a specific
point to play.
PROGRAMMED PLAY (CD/USB/MP3)
Programmed play is that tracks on the disc or on the USB can be edited for playback in a
preferred order with the use of PROGRAM button.
HANDLE DISC ONLY AS SHOWN
CLEAN FROM CENTER TO EDGE
DO NOT STORE NEAR HEAT
3