Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY AND ADJUSTMENTS
RAISE OR LOWER THE TABLE (FIG. 11)
1. Loosen the support lock handle (Fig. 11 - 1) and turn
the crank handle (Fig. 11 - 2) until the table is at
the desired height.
2. Tighten the support lock handle before drilling.
ROTATE THE TABLE (FIG. 11)
1. Loosen the support lock handle (Fig. 11 - 1) and turn
the table around the column to the desired position.
NOTE: The rack should rotate around
the column with
the table support
bracket. If the rack
binds and does not
rotate, slightly
loosen the set
screw in the rack
collar.
2. Tighten the
support lock
before drilling.
TILT THE TABLE (FIG. 12A)
1. Loosen the bevel lock bolt (Fig. 12A - 1)
by turning it counterclockwise with an
adjustable wrench (not included).
2. Tilt the table to the desired angle,
using the bevel scale (Fig. 12A - 2) as a basic guide.
3. Re-tighten the bevel lock bolt.
ADJUST TABLE TO
BE HORIZONTAL (FIG. 12A)
1. Loosen the bevel lock bolt
(Fig. 12A - 1).
2. Realign the table to the 0°
setting on the bevel scale
(Fig. 12A - 2).
3. Tighten the bevel
lock bolt with the
adjustment wrench.
INSTALL THE TABLE
EXTENSION (FIG. 12B)
1. Insert the two rods
(Fig. 12B - 1) of
the table extension
into the two channels
(Fig. 12B - 2) at
the side of the table.
2. Place a wing knob
(Fig. 12B - 3) in the
opening on the bottom
of each channel and
tighten to secure the
extension to the table.
WARNING
To avoid
injury, make sure the
chuck key is removed from
the chuck before starting
any drilling operation.
2
2
Fig. 12A
1
1
3
Fig. 12B
INSTALLING A DRILL BIT (FIG. 13)
1. Place the chuck key (Fig. 13 - 1) into the side keyhole of
the chuck (Fig. 13 - 2), meshing the key with the gear
teeth.
2. Turn the chuck key counterclockwise to open the chuck
jaws (Fig. 13 - 3).
3. Insert a drill bit (Fig. 13 - 4) into the chuck far enough to
obtain the maximum grip of the chuck jaws on the bit
shank.
4. Center the drill bit in the chuck jaws before the final
tightening of the chuck.
5. Tighten the chuck jaws using the chuck key to ensure that
the drill bit will not slip while drilling. Tighten all three
keyholes on the chuck.
6. Remove the
chuck key and
place it back on
the onboard
storage.
1
Fig. 11
SQUARING TABLE TO THE DRILL BIT (FIG. 14)
1. Insert a 3" long drill bit (Fig. 14 - 1) into the chuck
(Fig. 14 - 2) and tighten the jaws with the chuck key.
2. Raise the table with the crank handle (Fig. 14 - 3).
Lock the table (Fig. 14 - 4) approximately 1" below
the drill bit.
3. Place a combination square (Fig. 15 - 5) (not included)
on the table as shown, placing the long straight edge of
the combination square against the drill bit. Make sure
the drill bit is parallel / aligned exactly to the straight
edge of the square.
4. If an adjustment is needed, loosen the bevel lock bolt
(Fig. 14 - 6) with a wrench.
5. Tilt the table slightly, until
the combination straight
edge is aligned perfectly
with the drill bit.
6. Tighten the bevel
lock when square.
2
8
1
Fig. 13
4
2
1
5
4
6
Fig. 14
2
3
3
Publicidad
